Kenmore 625.38376 owner manual House Main Water Shutoff Valves, Single Bypass, Leak Test

Page 15

LEAK TEST

To check for leaks, complete the following steps:

CAUTION: To avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be

sure to do the following steps exactly asShu_ instructed.

HOUSE MAIN WATER

SHUTOFF VALVES

Water

¢--_:h_ Pressure Tank

1.Fully open two cold, soft water faucets near the softener.

2.Look at the pictures in Fig. 18 and 19 to deter- mine your kind of bypass valve(s). Place bypass valve(s) in "bypass" position. On a single valve, slide the stem inward to bypass. On a three (3) valve system, close the inlet and outlet valves and open the bypass valve.

3.Fully open the house main water pipe shutoff

valve. Observe steady water flow from both open faucets.

4.Place bypass valve(s) in SERVICE EXACTLY as follows: Keep soft water faucets open.

a. Single Bypass Valve: Slowly, slide pull the valve stem outward toward service, pausing sev- eral times to allow the softener to pressurize slow- ly.

b. Three Valve Bypass: Fully close the bypass valve and open the outlet valve. Slowly, open the inlet valve, pausing several times to allow the sof- tener to pressurize slowly.

5.After about three minutes, open a hot water faucet for about one minute, or until all air is expelled, then close.

6.Close both cold water faucets.

7.Check your plumbing work for leaks and fix right

away if any are found. Be sure to observe previ- ous caution notes.

NOTE: If this procedure is performed on a new softener, water coming from the taps may initial-

ly be discolored. This normally occurs the first time water runs through the resin bed. The dis- colored water is not harmful, and the discol- oration will not last more than a few minutes.

FOR SERVICE

Close bypass valve. Open inlet & outlet valves.

FOR BYPASS

Open bypass valve. Close inlet & outlet valves.

Meter Shutoff Valve / "1"-

Well Pump

FIG. 17

SINGLE BYPASS

Pull Stem Outward

For Service

_Push Inward

For Bypass

Note: Stem may be installed in either direction. The end

with writing should be pulled out for service position.

FIG. 18

VALVE BYPASS

Bypass

Outlet i

"

Valve

ValveInlet

Valve

FIG. 19

Questions? Call The Kenmore Water Line 1-800-426-9345

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerThree Year Limited Warranty on Electronic Parts TEN Year Limited Warranty Against LeaksQuestions? Page Parts Descriptions Small Parts InspectshipmentPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededValve Where to Install the Water SoftenerDraw Your Pipes Fittings Suggested Slab Foundation InstallationOUT FIG. a Before Installing Checks & TestsAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors Installing Holding Clips Valve BypassBypass Valve Turned Downward Connect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseHouse Main Water Shutoff Valves Single BypassLeak Test Cold Water Pipe Grounding Installgroundingclampbetween Thesoftenerinand OUT PipesWater Meter Jumper Wire Connecting TransformerIC ,IIU InstallcoversProgram the Timer Restart the Water HeaterSET Regeneration Time SET Present Time of DAYSET Water Hardness Number Hardness NumberSanitize Your Water Softener AS Follows Sanitize the Water SoftenerAddingsalttothe Storagetank Water Softening Salt with IronRemoving Additives Unit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallSalt Monitor System ExtrarechargeRecharge NOW Recharge TonightCalifornia Efficiency Requirement Clean Feature Clean Feature Minutes 97% Feature12 / 24 Hour Clock Gallons / Liters Maximum Days Between RegenerationsWater Flow Through the Softener Tank LightAverage Dally Gallons or Liters Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureSoft Water Service and Regeneration ServiceRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseSoft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeKeeping the Water Softener Clean Nozzle & Venturi Cleaning NozzleIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerProblemcause Checklist to Help YOU Save MoneyCorrection Bypass Valves Model 383760 Timer Code H Model 393760 Timer Code HPressure Drop PSI vs. Flow Rate GPM Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstMost Likely Less Likely Possible ProblemProcedure for Removing Error Code From Faceplate Manual Initiated Electronics DiagnosticsTimer PWA Replacement Troubleshooting Valve Position IndicatorsCycle Flow Rates Gallons PER MIN Checks, and the manual initiated diagnosticsFloat Setting Manualadvanceregeneration CheckTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line Part Number Part Description Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 29.92 Kb Manual 48 pages 24.39 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents