Kenmore 625.38376 owner manual Problemcause, Correction, Checklist to Help YOU Save Money

Page 32

CHECKLIST TO HELP YOU SAVE MONEY

If your water softener fails to work, make the following easy checks. Often, you will find what is wrong yourself and you won't have to call and wait for service. If you do not find anything wrong, while making the checks, and your sof- tener still does not work, call your Sears Service Department.

1.Also read ERROR CODE.

2.If an error code is not displayed, press and hold the SELECT1 button until the display changes. Then, press the SELECT1 button again and hold until a flashing code appears. It must show H 32 for Model 38376 or H 33 for Model 39376. If any other number shows, the face plate computer is working on incorrect input and would proba- bly be the cause of the problem. To set the correct code, press either the UP or DOWN button. When correct model code shows, press SELECT1 to return a flashing 12:00 AM display. Reset the present time, hardness num- ber, etc.

PROBLEMCAUSE

No soft water

No salt (or salt bridged) in the storage tank

CORRECTION

Add salt, see page 20, or break the salt bridge, see page 29. Press REGENERATION button and hold to start a regeneration, see page 22.

Water hard sometimes

Brine tank flooded

Salty tasting water

immediately after regeneration

Transformer unplugged at the watt outlet, or power cable leads loose from the electronic

board, fuse blown, circuit breaker popped, or circuit switched off.

Manual bypass valve(s) in bypass position

Dirty, plugged or damaged nozzle venturi

Valve drain hose plugged or restricted

Hardness number setting too low

Using hot water when softener is regenerat- ing

Increase in the grains of hardness in your water supply

Restricted drain line

Plugged or dirty nozzle & venturi

Valve rotor-disc & seals

Restricted drain line

Check for loss of power due to any of these and correct. With the power back on, look at the time display and read PROGRAM MEMO- RY, see page 25.

Look at Fig. 18 & 19 on page 15. Move the stem in a single valve to service. In a 3-valve bypass, open the inlet and outlet valve, and be sure to fully close the bypass valve.

Take apart and clean or replace damaged parts, see page 30.

The drain hose must not have kinks, sharp bends, or be raised too high above the soften- er, see page 14.

Press and release the SELECT button until HARDNESS shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown

as on your water analysis report. See page 19 to reset. Press and release the SELECT button

until the present time shows in the display.

Avoid using hot water during this time because the water heater refills with hard water, see Automatic Bypass, page 28.

Ask your Sears retail store for a new water analysis. Then make a new hardness number setting, page 18.

Check for kinks, bends or obstructions, see page 14.

Take apart and clean or replace damaged parts, see page 30.

Check for scratches or grooves, replace if needed.

Check for kinks, bends or obstructions, see page 14.

Questions? Call The Kenmore Water Line 1-800-426-9345

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Repair or Parts ? Call toll free Save this ManualONE Year Limited Warranty on Water Softener Three Year Limited Warranty on Electronic PartsTEN Year Limited Warranty Against Leaks Disclaimer of implied warranties limitation of remediesQuestions? Page Inspectshipment Parts Descriptions Small PartsProper Order to Install Water Treating Equipment Plan Your InstallationTools Needed PipeWhere to Install the Water Softener ValveSuggested Slab Foundation Installation Draw Your Pipes FittingsOUT Before Installing Checks & Tests FIG. aInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Bypass Valve Turned Downward Installing Holding ClipsValve Bypass Position Softener Into Place Connect the SoftenerConnect the Valve Drain Hose Connect Salt Tank Overflow TubingLeak Test House Main Water Shutoff ValvesSingle Bypass Installgroundingclampbetween Thesoftenerinand OUT Pipes Water Meter Jumper WireConnecting Transformer Cold Water Pipe GroundingInstallcovers Program the TimerRestart the Water Heater IC ,IIUSET Present Time of DAY SET Water Hardness NumberHardness Number SET Regeneration TimeSanitize the Water Softener Sanitize Your Water Softener AS FollowsRemoving Additives Addingsalttothe StoragetankWater Softening Salt with Iron Check List of STEP-BY-STEP Guides to Install Unit plugged Into a continuously live outlet?Extrarecharge Recharge NOWRecharge Tonight Salt Monitor SystemClean Feature Clean Feature Minutes 97% Feature 12 / 24 Hour ClockGallons / Liters Maximum Days Between Regenerations California Efficiency RequirementTank Light Water Flow Through the SoftenerRecharge Time Remaining and Valve Position Indicators Error CodeKenmores Ultra Cleansing Feature Average Dally Gallons or LitersRegeneration Soft Water Service and RegenerationService Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashElectronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener Clean Nozzle & VenturiCleaning Nozzle Drain ALL Water from Softener Protect the Water Softener from FreezingCorrection ProblemcauseChecklist to Help YOU Save Money Model 383760 Timer Code H Model 393760 Timer Code H Bypass ValvesPressure Drop PSI vs. Flow Rate GPM Wiring Schematic FaceplateAlways Make These Initial Checks First Eration CheckPossible Problem Procedure for Removing Error Code From FaceplateManual Initiated Electronics Diagnostics Most Likely Less LikelyTroubleshooting Valve Position Indicators Timer PWA ReplacementChecks, and the manual initiated diagnostics Float SettingManualadvanceregeneration Check Cycle Flow Rates Gallons PER MINRotaryvalveservice DisassemblyAssembly To Relieve PressureValve Service Cycle Water Flow Through the SoftenerFill Cycle Brining and Brine Rinse CycleValve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line Water Softener Complete Part Number Part DescriptionInlet Outlet Grounding Clamps Brine Valve Assembly Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 29.92 Kb Manual 48 pages 24.39 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents