Kenmore 625.38376 Rotaryvalveservice, To Relieve Pressure, Disassembly, Servicing the Valve

Page 39

ROTARYVALVESERVICE

IMPORTANT: Before working on the valve, turn off the water supply and disconnect from electrical power.

TO RELIEVE PRESSURE:

•3 VALVE BYPASS: Close the inlet valve and open a soft water faucet. Then close the outlet valve and open the bypass valve.

•SEARS SPECIAL BYPASS: Slide the bypass valve stem to bypass position. Loosen three hex head screws toward the back side of the valve to allow pressure water to bleed out. Catch water with a rag.

DISASSEMBLY

To remove a part or group of parts, refer to the valve drawing. A common screwdriver or nut driver, Phillips screwdriver and pliers are the only tools needed to com- pletely disassemble.

SERVICING THE VALVE

Inspect all o-rings, seals and gaskets for wear or defects.

Inspect the bottom surface of the rotor for scratches, chips or wear.

Note: If replacement is needed, be sure to use the current replacement part.

ASSEMBLY

Be sure all parts are in place and in the proper position. Lubricate ALL o-rings and seals with FDA approved sili- cone grease. To install the rotor seal, first place the seal into the valve groove, rounded side down (see cross-sec- tion). Apply a light coating of silicone grease to the seal's crossing ribs. Then, carefully center the wear strip on the seal, and push it downward onto the seal.

Install the nozzle and venturi seal and drain seal. Assemble wave washer bearing, the wave washer, and two o-rings, onto the rotor top shaft. Then center the rotor in the valve body, on the rotor seal.

Lower the cover onto the valve body and rotor shaft. Then install the cover holding screws. Before tightening the screws, install the valve cam and gear.

Then, turn the rotor (clockwise only) to service position. Tighten the screws using a criss-cross pattern. If a torque wrench is available, torque to 30-40 inch pounds. Do not over tighten.

Lubricate the gear on the motor, and the valve cam gear with Molykote grease, or other high quality gear lubricant.

Be sure to orient switch as shown, with lever toward the cam.

Sensor

Housing

See Nozzle

Assembly Service

FIG. 66

Questions? Call The Kenmore Water Line 1-800-426-9345

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerThree Year Limited Warranty on Electronic Parts TEN Year Limited Warranty Against LeaksQuestions? Page Parts Descriptions Small Parts InspectshipmentPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededValve Where to Install the Water SoftenerDraw Your Pipes Fittings Suggested Slab Foundation InstallationOUT FIG. a Before Installing Checks & TestsAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors Installing Holding Clips Valve BypassBypass Valve Turned Downward Connect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseHouse Main Water Shutoff Valves Single BypassLeak Test Cold Water Pipe Grounding Installgroundingclampbetween Thesoftenerinand OUT PipesWater Meter Jumper Wire Connecting TransformerIC ,IIU InstallcoversProgram the Timer Restart the Water HeaterSET Regeneration Time SET Present Time of DAYSET Water Hardness Number Hardness NumberSanitize Your Water Softener AS Follows Sanitize the Water SoftenerAddingsalttothe Storagetank Water Softening Salt with IronRemoving Additives Unit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallSalt Monitor System ExtrarechargeRecharge NOW Recharge TonightCalifornia Efficiency Requirement Clean Feature Clean Feature Minutes 97% Feature12 / 24 Hour Clock Gallons / Liters Maximum Days Between RegenerationsWater Flow Through the Softener Tank LightAverage Dally Gallons or Liters Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureSoft Water Service and Regeneration ServiceRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseSoft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeKeeping the Water Softener Clean Nozzle & Venturi Cleaning NozzleIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerProblemcause Checklist to Help YOU Save MoneyCorrection Bypass Valves Model 383760 Timer Code H Model 393760 Timer Code HPressure Drop PSI vs. Flow Rate GPM Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstMost Likely Less Likely Possible ProblemProcedure for Removing Error Code From Faceplate Manual Initiated Electronics DiagnosticsTimer PWA Replacement Troubleshooting Valve Position IndicatorsCycle Flow Rates Gallons PER MIN Checks, and the manual initiated diagnosticsFloat Setting Manualadvanceregeneration CheckTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line Part Number Part Description Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 29.92 Kb Manual 48 pages 24.39 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents