Woodstock M1103, M1102 owner manual Set Up, Unpacking, Inventory

Page 12

M1102/M1103 16-Speed Drill Press

SET UP

UP

Unpacking

Get lifting assistance before starting assembly. The Model M1102/M1103 drill press is heavy. DO NOT attempt to lift it without help!

Your drill press has been carefully packaged for safe transporting. If you notice the machine has been dam- aged, please contact your authorized SHOP FOX® dealer immediately.

Inventory

If any parts are missing, examine the pack- aging for the missing parts. For any missing parts, find the part number in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at tech-support@shopfox.biz

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and pack-

ing materials to elimi-

nate choking/suffocation

hazards for children and

animals.

SET

Note: Some parts and hardware may already be

 

 

 

 

 

installed on the machine. Make sure to check the

 

 

 

 

 

machine when you use this inventory list.

 

 

 

 

 

Inventory (Figure 2)

Qty

1

 

2

3

 

 

 

 

 

 

 

 

 

 

 

1.

Headstock Assembly ....................................1

 

 

 

 

2.

Arbor ......................................................1

 

 

 

 

3.

Chuck Guard..............................................1

4

 

 

 

4.

Chuck Key.................................................1

 

 

 

 

5

 

 

5.

Drift Key ..................................................1

 

 

 

 

 

 

 

6.

Chuck ......................................................1

 

6

 

 

7.

Knob .......................................................3

 

 

 

7

8.

Downfeed Handles ......................................3

 

 

 

 

 

 

8

9.

Table ......................................................1

 

 

 

 

 

 

 

10.

Table Support Assembly ................................1

 

 

 

 

11.

Handle.....................................................1

 

 

9

 

12.

Column Model M1102 ...................................1

 

 

 

 

 

 

 

13.

Column Model M1103 ...................................1

 

 

 

 

14.

Column Support Lock Lever............................1

12

 

10

 

15.

Crank Handle.............................................1

 

 

 

11

16.

Base........................................................1

 

 

 

 

 

 

 

17.

Table Lock Lever ........................................1

 

14

 

 

18.

Hardware Bag (Not Shown) ............................1

 

 

 

 

 

—Belt Cover Knob .......................................1

 

17

 

 

 

—Hex Wrench 3mm......................................1

 

 

15

 

 

 

 

 

—Hex Wrench 4mm......................................1

13

 

 

 

 

—Hex Bolt M8-1.25 x 25mm (Base) ...................4

 

 

16

 

 

—Lock Washer 8mm (Base) ............................4

 

 

 

 

Figure 2. M1102/M1103 box inventory.

-10-

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Speed Drill Press Page Contents Service Introduction Woodstock Technical SupportAbout Your New 16-Speed Drill Press M1102 Specifications M1103 SpecificationsIdentification Cast Iron Base with T-Nut Slots Allows for maxiSafety Safety Instructions for MachineryBefore Operating this Machine Always Lock Mobile Bases if Used Before Operating Machinery Safety for Drill Presses Electrical 110V OperationExtension Cords GroundingSET UP UnpackingInventory Machine Placement Cleaning MachineTo install the table support Column and BaseTable Support To secure the column to the base, do these stepsSliding table support and rack Over the column Headstock Aligning headstock with a Typical drill press baseTo install the chuck guard, do these steps Chuck GuardDrill Chuck & Arbor Seating arbor into chuck To install the downfeed handles, do these steps To install the table, do these stepsDownfeed Handles & Belt Cover Knob Work Light Test RunTo test run the drill press Mounting To mount the Model M1102 drill press to a tableInstalling & Removing Drill Bits To install a drill bit, do these stepsOperations GeneralChanging Spindle RPM To change spindle RPM, do these stepsAdjusting Table Tilt Depth StopTo set the depth stop, do these steps To tilt the table, do these stepsOperations Operations Arbor Removal To remove the drill chuck and arbor, do these stepsMaintenance BeltsTable and Base LubricationService TroubleshootingM1102/M1103 16-Speed Drill Press Drill Press Operations Feed Shaft Spring Tension Electrical Components Capacitor110V Wiring Diagram M1102/M1103Wiring Diagram PartsService Notes M1102/M1103 Parts Diagram M1102/M1103 Parts List PART# DescriptionWiringharness Label Placement and Parts REF PART# DescriptionParts Notes Warranty Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents