Woodstock owner manual M1102 Specifications, M1103 Specifications

Page 6

INTRODUCTION

 

M1102/M1103 16-Speed Drill Press

 

 

 

M1102 Specifications

Motor Type:

TEFC Capacitor Start Induction

Motor:

1/2 HP, 110V, 8.5 Amp., Single-Phase ⁄ 60 Hz

RPM:

1725

Power Transfer:

V-Belt Drive

Bearings:

Shielded & Lubricated Ball Bearings

Power Switch:

Toggle ON/OFF Switch, w/ Safety Lock Key

Lamp Switch:

Rocker Type ON/OFF Switch

Spindle Travel:

33/16''

Maximum Distance, Spindle to Base:

241/4''

Maximum Distance, Spindle to Table:

17''

Floor to Table Top Height:

87/8'' to 251/4"

Overall Height:

39''

Footprint:

195/8'' to 12"

Table Tilt:

45° Left and Right

Table Rotation:

360°

Spindle Taper:

MT#2

Spindle to Column Distance:

61/2"

Chuck Size:

5/8'' (1-16mm JT3), Keyed

Speed and Drive:

16, Belt Controlled

Speeds: 230, 332, 376, 470, 544, 569, 653, 760, 813, 840, 1458, 1610, 1716, 2196, 2375, 3270. RPM

Machine Weight:

108 lbs.

Shipping Weight:

117 lbs.

M1103 Specifications

Motor Type:

TEFC Capacitor Start Induction

Motor:

1/2 HP, 110V, 8.5 Amp., Single-Phase ⁄ 60 Hz

RPM:

1725

Power Transfer:

V-Belt Drive

Bearings:

Shielded & Lubricated Ball Bearings

Power Switch:

Toggle ON/OFF Switch, w/ Safety Lock Key

Lamp Switch:

Rocker Type ON/OFF Switch

Spindle Travel:

33/16''

Maximum Distance, Spindle to Base:

48''

Maximum Distance, Spindle to Table:

303/4''

Floor to Table Top Height:

195/8'' to 451/4"

Overall Height:

62''

Footprint:

195/8'' to 12"

Table Tilt:

45° Left and Right

Table Rotation:

360°

Spindle Taper:

MT#2

Spindle to Column Distance:

61/2"

Chuck Size:

5/8'' (1-16mm JT3), Keyed

Speed and Drive:

16, Belt Controlled

Speeds: 230, 332, 376, 470, 544, 569, 653, 760, 813, 840, 1458, 1610, 1716, 2196, 2375, 3270. RPM

Machine Weight:

128 lbs.

Shipping Weight:

132 lbs.

-4-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Speed Drill Press Page Contents Service Introduction Woodstock Technical SupportAbout Your New 16-Speed Drill Press M1102 Specifications M1103 SpecificationsIdentification Cast Iron Base with T-Nut Slots Allows for maxiSafety Safety Instructions for MachineryBefore Operating this Machine Always Lock Mobile Bases if Used Before Operating Machinery Safety for Drill Presses Extension Cords Electrical110V Operation GroundingSET UP UnpackingInventory Machine Placement Cleaning MachineTable Support To install the table supportColumn and Base To secure the column to the base, do these stepsSliding table support and rack Over the column Headstock Aligning headstock with a Typical drill press baseTo install the chuck guard, do these steps Chuck GuardDrill Chuck & Arbor Seating arbor into chuck To install the downfeed handles, do these steps To install the table, do these stepsDownfeed Handles & Belt Cover Knob Work Light Test RunTo test run the drill press Mounting To mount the Model M1102 drill press to a tableOperations Installing & Removing Drill BitsTo install a drill bit, do these steps GeneralChanging Spindle RPM To change spindle RPM, do these stepsTo set the depth stop, do these steps Adjusting Table TiltDepth Stop To tilt the table, do these stepsOperations Operations Arbor Removal To remove the drill chuck and arbor, do these stepsTable and Base MaintenanceBelts LubricationService TroubleshootingM1102/M1103 16-Speed Drill Press Drill Press Operations Feed Shaft Spring Tension Electrical Components Capacitor110V Wiring Diagram M1102/M1103Wiring Diagram PartsService Notes M1102/M1103 Parts Diagram M1102/M1103 Parts List PART# DescriptionWiringharness Label Placement and Parts REF PART# DescriptionParts Notes Warranty Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents