Inova SX150-BHF Tool Operation, Before Handling or Operating this Tool, Contact Trip Operation

Page 9

TOOL OPERATION

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

BEFORE HANDLING OR OPERATING THIS TOOL:

I.READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

II.REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL.

There are three available systems on BOSTITCH pneumatic tools. They are:

1. CONTACT TRIP OPERATION 2. SEQUENTIAL TRIP OPERATION 3. TRIGGER OPERATION

OPERATION

1. CONTACT TRIP OPERATION:

The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. There are two methods of operation to drive fasteners with a contact trip tool.

A. SINGLE FASTENER PLACEMENT: To operate the tool in this manner, first position the contact trip on the work surface, WITHOUT PULLING THE TRIGGER. Depress the contact trip until the nose touches the work surface and then pull the trigger to drive a fastener. Do not press the tool against the work with extra force. Instead, allow the tool to recoil off the work surface to avoid a second unwanted fastener. Remove your finger from the trigger after each operation.

B. RAPID FASTENER OPERATION: To operate the tool in this manner, hold the tool with the contact trip pointing towards but not touching the work surface. Pull the trigger and then tap the contact trip against the work surface using a bouncing motion. Each depression of the contact trip will cause a fastener to be driven.

The operator must not hold the trigger pulled on contact trip tools except during fastening operation, as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven, possibly causing injury.

2.SEQUENTIAL TRIP OPERATION:

The SEQUENTIAL TRIP MODEL contains a contact trip that operates in conjunction with the trigger to drive a fastener. To operate a sequential trip tool, first position the contact trip on the work surface WITHOUT PULLING THE TRIGGER. Depress the contact trip and then pull the trigger to drive a fastener. As long as the contact trip is contacting the work and is held depressed, the tool will drive a fastener each time the trigger is depressed. If the contact trip is allowed to leave the work surface, the sequence described above must be repeated to drive another fastener.

3.TRIGGER OPERATION:

A TRIGGER OPERATED tool requires a single action to drive a fastener. Each time the trigger is pulled the tool will drive a fastener. The trigger operated model is intended for use only when a contact trip or sequential trip cannot be used due to the requirements of the application.

-9-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Stanley Fastening Systems L.P Index IntroductionAIR Supply and Connections Safety InstructionsLoading Tool OperationFastener Specifications Tool SpecificationsTool AIR Fitting Operating PressureSequential Trip Contact TripTrigger Operated Model IdentificationHoses FittingsSupply Source RegulatorTo Prevent Accidental Injuries Loading the SL150, SX150, LHF97125, USO56, SL125OC, S97125BOSTITCH, INC DIAL-A-DEPTH Fastener Control AdjustmentBefore Handling or Operating this Tool Tool OperationContact Trip Operation Sequential Trip OperationMaintaining the Pneumatic Tool Tool Operation CheckProblem Cause Correction Trouble ShootingIntroducción ÍndiceNota Suministro DE Aire Y Conexiones Instrucciones DE SeguridadAL Cargar LA Herramienta OperaciónEspecificaciones DE GRAPAS/PUNTAS Especificaciones DE LA HerramientaConector DE Aire DE LA Herramienta Presión Opera TivaDisparo Secuencial Disparo POR ContactoOperación POR GA Tillo Identificación DE ModeloMangueras ConexionesFuente DE Suministro ReguladorAdvertencia Para Impedir Lesiones Accidentales Carga DE LOS Modelos SL150, SX150, LHF97125, USO56Ajuste DE Control DE Engrapado DIAL-A-DEPTH Antes DE Manejar U Operar Esta Herramienta Operación DE LA HerramientaOperación DE Disp ARO POR Contacto Operación DE Disp ARO SecuencialMantenimiento DE LA Herramienta Neumática Verificación DE LA Operación DE LA HerramientaDiagnóstico DE Falla Problema Causa CorrecciónRemarque IndexeAlimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéChargement DE L’APPAREIL FonctionnementSpécifica Tions DES Dispositifs DE Fixation Spécifications DE L’OUTILGarniture Pneumatique Pression DE FonctionnementDéclenchement À LA Volée OpérationDéclenchement AU COUP-PAR-COUP Déclenchement P AR DétenteTuyaux RaccordementsAlimentation EN AIR Comprimé Régula TeurPour Prévenir UN Accident Chargement DE SL150, SX150, LHF97125, USO56 SL125OC, S97125Commande DE Réglage DES Dispositifs DE Fixation DIAL-A-DEPTH Mode D’EMPLOI Fonctionnement DE L’APPAREILAvant DE Manipuler OU D’UTILISER CET Outil Vérification DU Système DE Déclenchement Maintenance DE L’OUTIL PneumatiqueProblème Cause Correction Problèmes DE Fonctionnement

S97125, SX150, SX150-BHF, BT125, SL125OC specifications

The Inova USO56, LHF97125, SL150, BT200, and SL125OC are advanced LED lighting solutions designed for various applications, including commercial, industrial, and residential lighting. Each model brings unique features and cutting-edge technology that cater to different user needs.

Starting with the Inova USO56, this robust LED solution is designed for high-efficiency performance in demanding environments. It utilizes a durable construction that withstands harsh conditions, making it ideal for outdoor applications. The USO56 is equipped with energy-efficient LED chips that provide superior brightness while consuming minimal power. Its advanced thermal management system ensures optimal performance and longevity, reducing the need for frequent replacements and maintenance.

The LHF97125 model, on the other hand, focuses on versatility and adaptability. This fixture features adjustable brightness levels, allowing users to customize the light output according to their specific requirements. The LHF97125 includes smart technology capabilities, enabling integration with building management systems for enhanced energy savings. Its sleek design makes it suitable for modern office spaces, retail environments, and public areas.

The SL150 is another standout product, specifically designed for high-traffic zones. This LED lighting solution offers exceptional durability with an IP65 rating, making it resistant to dust and water ingress. The SL150 is equipped with motion-sensing technology, providing automatic illumination in response to movement, which enhances energy efficiency and security. Its flexible mounting options and compact design allow for easy installation in various settings.

The BT200 model is renowned for its innovative smart features. It comes with built-in Wi-Fi connectivity, allowing users to control lighting remotely via a smartphone app. The BT200 supports various lighting modes and schedules, giving users complete flexibility in managing their lighting needs. This model is particularly popular for residential applications, where convenience and atmosphere are paramount.

Lastly, the SL125OC offers a blend of elegance and functionality. With an ultra-slim profile, this model is perfect for spaces where aesthetics are a priority. The SL125OC features dimmable capabilities and utilizes energy-efficient LED technology, making it an eco-friendly choice for homeowners and businesses alike. Its easy installation process makes it accessible for anyone looking to upgrade their lighting without extensive renovations.

In conclusion, the Inova USO56, LHF97125, SL150, BT200, and SL125OC each bring unique features and technologies to the lighting market, addressing the diverse needs of users across different sectors. With a commitment to energy efficiency, durability, and smart technology, Inova continues to push the boundaries of lighting innovation.
Top Page Image Contents