Firestone EMDG198 manual Static Data, Available with a bead ring. Bolts are not included, 140, 310

				-
1T15M 0
													CONSULT FIRESTONE									RECOMMENDED			Static Data
					Description				Assembly Order No.				BEFORE USING AS									AIRMOUNT
																						DESIGN HEIGHT			8826
														AIRMOUNT
		Style		Blind nuts, 1/4 NPT					WO1-358-9030													7.5 INCHES
	1T15M-0			Blind nuts, 1/4 NPT,
				rubber bumper					WO1-358-9031
		Two
															Do not use Airstroke					in
		Ply		Blind nuts, 3/4 NPT					WO1-358-9034															120 Psig
															shaded area without
		Bellows		Blind nuts, 3/4 NPT,
														9	consulting Firestone													9
				rubber bumper					WO1-358-9036
															Volume
				Countersunk steel bead ring,
				13/8 bolts, nuts, washers					WO1-358-9038					8	100 Psig													8
				Integral studs, 1/4 NPT					WO1-358-9035				100x
																								100 Psig
	Assembly weight ...................................................... 11.5 lbs.
													IN.	7														7
		3/8-16 BLIND NUTS									1/4 OR 3/4 NPT		CUBUMPER)(WITHOUT	6											80 Psig			6	1000xLBSFORCE
		(5/8 DEEP)					AT 100 PSIG
												AIR INLET
		15-20 FT. LBS.									2.88			5														5
			TORQUE
																									60 Psig
														4														4
								6.20
						12.8 MAX O.D.
							9.00 DIA.						VOLUME	2														2
														3										40 Psig				3
		25-30 FT. LBS.					OPTIONAL			HEIGHT
			TORQUE				BUMPER																		20 Psig
		1/2-13 THREADED HOLE
		(3/4 DEEP)							1.96					1														1
		(TWO IN PISTON)
						4.12
							9.50 DIA.
	NOTE: Bellows will not compress properly with less													0														0
	than 10 PSIG internal pressure.
														MAX. HT.													MIN. HT.
														13	12	11			10		9	8	7	6		5	4.3
	NOTE: A bead plate part is shown. This part is also																		HEIGHT IN.
	available with a bead ring. Bolts are not included.																							BUMPER CONTACT
	See pages 8-10 for explanation.																								5.3 IN.
															See page 12 for instructions on how to use chart.
		Dynamic Characteristics at 7.5 in. Design Height													Force Table (Use for Airstroke®								actuator design)
		(Required for Airmount isolator design only)
																Volume						Pounds Force
		Volume @ 100 PSIG = 498 in3								Natural					Assembly	@ 100
															Height		PSIG		@20		@40	@60		@80	@100
									Frequency						(in.)			(in3)	PSIG		PSIG		PSIG	PSIG		PSIG
		Gage					Spring
		Pressure			Load			Rate	CPM			HZ			11.0	737			980		1,920	2,980		4,120	5,300
		(PSIG)			(lbs.)		(lbs./in.)								10.0	675			1,180		2,310	3,550		4,810	6,130
	40				2,670	793			102			1.71
															9.0	606			1,270		2,540	3,910		5,290	6,710
	60				4,120	1,105			97			1.62			8.0	534			1,300		2,630	4,080		5,500	6,950
															7.0	462			1,320		2,690	4,140		5,570	7,010
	80				5,540	1,399			94			1.57
															6.0	389			1,350		2,730	4,170		5,610	7,070
	100				6,990	1,690			92			1.54
															5.0	314			1,410		2,840	4,310		5,840	7,370

92