Fedders A7Q08F2B Power Control, Set Temperature/Timer Display, Temperature/Timer Hour Controls

Page 5

B

C

F

E

D

A

A.Power Control

B.Set Temperature/Timer Display

C.Temperature/Timer Hour Controls

D.Mode Control

E.Fan Speed Control

F.Timer Control

Built-in three minute timing delay.

If this electronic unit will not respond to touch pad or remote control commands, it is necessary to unplug the unit from the electrical outlet for five seconds and then plug the unit back in.

Auto restart feature:

In the event of a power failure, this feature allows the unit to resume operation once power has been restored, retaining the most recent settings. Upon restoration of power, the timer mode may need to be reset if being utilized.

CAUTION

Heat/Cool models or units with electric heat are designed to be used only as a supplemental heat source. They should be used in addition to regular heating systems and never as the primary source of heat.

OPERATION

Power Control

The Power Control turns the unit on and off.

Set Temperature/Timer Display

Shows the set temperature when the unit is in operation and hours when the timer is being set. THE TEMPERATURE DISPLAY ONLY SHOWS THE SET TEMPERATURE, NOT THE ACTUAL ROOM TEMPERATURE.

Temperature/Timer Hour Controls

These buttons are used to raise or lower the set temperature in increments of 1° from 66°F to 88°F. By depressing both buttons at once, the display will toggle between Celsius and Fahrenheit. When the timer is being set, these buttons are used to change the hour setting in increments of 1 from 00 to 24.

Check Filter Light/Reset (some models)

After 250 hours of usage the Check Filter light

will turn on. At this time, the filter needs to be removed and cleaned (see page 8). After the filter is cleaned and repositioned, depress the Reset

button. This will restart the counter and turn the light off.

Mode Control

A green light will indicate which mode is currently being utilized.

Cool Mode – The unit will circulate and cool the air.

Heat Mode (Heat Models Only)– The unit will circulate and heat the air.

Heater Safety Feature- When heater is powered off, low fan will automatically stay on and run for 60 seconds to ensure the removal of residual heat, meanwhile, the Low Fan LED blinks until the low fan stops.

Fan Mode – The unit will only circulate the air.

Energy Saver Mode –

(The energy saver mode is designed to operate with Cool mode only)

The fan will switch from the set fan speed to LO whenever the compressor turns off in response to the thermostat. When the compressor cycles back on, the unit will return to the original fan setting.

Fan Speed Control

High, Medium*, Low and Auto

The settings are adjusted with the Fan Speed Control, each time the button is depressed it changes the setting. A green light will indicate which setting is currently being used.

When the AUTO feature is selected while the air conditioner is in the COOL or HEAT mode, the fan speeds will change automatically as the temperature in the room changes.

COOL Mode

•7° or more above the set temperature will use HI FAN.

•4° or less above the set temperature will use LO FAN.

HEAT Mode (Heat models only)

•9° or more below the set temperature will use HI FAN.

•4° or less below the set temperature will use LO FAN.

*MEDIUM FAN NOT available on HEAT models.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Garantía EnglishImportant Grounding Requirements InstallationOr email customerservice@fedders.com Tools Needed Installation in Normal Width WindowWindow Requirements Unit & Window SizeInside View Installation in Minimum Width WindowSet Temperature/Timer Display Power ControlTemperature/Timer Hour Controls Check Filter Light/Reset some modelsAir Conditioner Remote Control Timer ControlTimer can be set to either turn the unit on or off To turn the unit on using the TimerOccurrence Possible Cause Solutions Cleaning Air FilterService Troubleshooting GuideRoom Air Conditioner Warranty How to Obtain Warranty Service or PartsWarranty ExceptionsRequerimientos Importantes para la Puesta a Tierra Riesgo de Choque EléctricoInstalacion Precauciones de Seguridad AdicionalesRequisitos de la ventana Herramientas necesariasTamaño de la ventana y de la unidad Instale los paneles de llenado En algunos modelosConsultar los pasos 1 a 7 de las instrucciones precedentes Instalación en una ventana de ancho mínimoPantalla de configuración de temperatura/reloj Control de alimentaciónControles de temperatura/hora del reloj Control de modoControl del reloj Control de velocidad del ventiladorControl Remoto de Acondicionador de Aire PRECAUCION´Localización y Solución de Averías Problema Causa Posible SolucionesOrientación de la corriente de aire Limpieza del filtro de aireGarantía del acondicionador de aire Cómo obtener servicio o piezas bajo la garantíaGarantia ExcepcionesAvertissement Risque de choc électriqueCordon électrique avec dispositif de détection darc Caractéristiques des fenêtres Dimensions de l’appareil et de la fenêtreFixation des panneaux de remplissage Pose dans une fenêtre de largeur normalePose dans une fenêtre de largeur minimum Commandes de la température et du nombre d’heures Commande marche/arrêtCommande du mode Commande de la vitesse de ventilationTélécommande de Climatiseur Commande de la minuteriePRECAUTION´ Symptôme Causes possibles SolutionsOrientation de l’air Nettoyage du filtre à airGarantie du climatiseur Pour les modèles installés en dehors de l’Amérique du NordDépannage ET Garantie 800 332-6658 ou en écrivant àPage 23-23-0321N-011

A7Q08F2B specifications

The Fedders A7Q08F2B is a versatile and efficient air conditioning unit designed to provide optimal comfort in residential and small commercial spaces. It stands out for its innovative technologies and user-friendly features, making it a reliable choice for consumers looking to enhance their indoor climate.

One of the key features of the A7Q08F2B is its powerful cooling capacity. With a cooling output of 8,000 BTUs, it effectively cools rooms measuring up to 350 square feet, ensuring a pleasant environment even during the hottest months. The unit also offers multiple fan speeds, allowing users to customize airflow according to their preferences.

Energy efficiency is another major highlight of the Fedders A7Q08F2B. The unit is equipped with an Energy Efficiency Ratio (EER) that meets and often exceeds regulatory standards. This means it uses less electricity without sacrificing performance, resulting in lower utility bills and a smaller carbon footprint. The energy-saving features also include a programmable timer and eco-friendly cooling mode, which further enhance its efficiency.

The design of the A7Q08F2B emphasizes user convenience. It includes a remote control that allows users to adjust settings from across the room, making it incredibly easy to operate. Additionally, the unit features an LED display, enabling instant feedback on temperature settings and operating modes.

The A7Q08F2B also focuses on air quality, incorporating a washable air filter that effectively traps dust, pet dander, and other airborne particles. This not only ensures cleaner air but also promotes healthier living conditions. The filter is easily accessible, requiring minimal effort for maintenance and cleaning.

In terms of installation, the Fedders A7Q08F2B is designed for straightforward setup, compatible with window installations. The detailed installation manual and included mounting hardware make it easier for homeowners to have the unit up and running quickly.

Overall, the Fedders A7Q08F2B encapsulates efficiency, ease-of-use, and effective cooling performance. With its advanced features and commitment to energy conservation, it remains a popular choice for those seeking reliable air conditioning solutions. Whether for a home office, bedroom, or small living area, this unit delivers the comfort and convenience needed for modern lifestyles.
Top Page Image Contents