Grizzly G9860 owner manual Stock Inspection Requirements, #/22%#4

Page 28

stock inspection

Stock Inspection &

Requirements

Follow these rules when choosing and joint- ing stock:

DO NOT joint or surface place stock that contains large or loose knots. Injury to the operator or damage to the workpiece can occur if a knot becomes dislodged during the cutting operation.

Jointing and surface planing with the grain is safer for the operator and pro- duces a better finish. Cutting against the grain increases the likelihood of kickback and workpiece tear-out. DO NOT cut against the grain! Cutting with the grain is feeding the stock across the cutterhead so the grain points down and toward you, as viewed from the edge of the stock (see Figure 34).

Note: If the grain changes direction along the edge of the workpiece, decrease the depth of cut and make additional passes.

#/22%#4

7ITH 'RAIN

).#/22%#4

!GAINSTI'RAIN

Figure 34. Proper grain alignment with the

cutterhead.

Only process natural wood fiber through your jointer. Your jointer is designed to cut only natural wood stock. Attempting to pro- cess any other synthetic or natural material will damage the cutterhead and cause injury hazards for the operator.

-26-

Scrape all glue off the workpiece before jointing. Glue deposits on the workpiece, hard or soft, will gum up the cutterhead and produce poor results.

Remove foreign objects from the workpiece. Make sure that any stock you process with the jointer is clean and free of dirt, nails, staples, tiny rocks or any other foreign objects, that could damage the cutterhead. These particles could also cause a spark as they strike the cutterhead and cre- ate a fire hazard.

Note: Wood stacked on a concrete or dirt surface can have small pieces of concrete or stone pressed into the surface.

Make sure all stock is sufficiently dried before jointing. Wood with a moisture con- tent over 20% will cause unnecessary wear on the cutters and poor cutting results. Excess moisture can also hasten rust and corrosion.

Make sure your workpiece exceeds the minimum dimension requirements, as shown in Figure 35, before processing it through the jointer, or the workpiece may break or kick back during the operation.

&'B^c#

&B^c#

&$'B^c#

&'B^c#

&$'B^c#

&B^c#

Figure 35. Minimum stock dimensions for the

jointer.

Extreme Series Jointer (Mfg. Since 9/11)

Image 28
Contents Extreme Series Jointer Ss ,EAD from Leadbased PAINTS Table of Contents Warranty and Returns Manual Accuracy Contact Info IntroductionMachine Description Identification Model Specification Comparison Safety Safety Instructions for MachineryChildren & BYSTANDERS. @ZZe XaYgZc ZghWZXdbZVYhigVXidc#Additional Safety Instructions for Jointers Power Supply AvailabilityFull-Load Current Rating Circuit InformationG9953ZXF Circuit Requirements for 220V Operation Circuit Requirements For G9953 G9953ZXG9953ZXF Circuit Requirements for 440V Operation Model G9953ZXF 440V Conversion Grounding RequirementsExtension Cords G9860, G9860ZX, G9953, & G9953ZX Only Replacing Contactor & Overload RelayRewiring Motor Replacing Control Panel Light BulbsSetup Needed for SetupUnpacking Description QtyInventory Clean Up Inventory Figure QtyPlacement Location Site ConsiderationsMounting to Shop Floor Floor LoadMoving Assembling Jointer Using Machine MountsMoving & Placing Jointer Infeed table stop bolt viewed from Underneath the table Installing Fence G9953/G9953ZX/ G9953ZXF Installing Fence G9860/G960ZXStep To set the outfeed table height Setting OutfeedModels G9953, G9953ZX, & G9953ZXF Cutter edge at top-dead-center Page OFF Button Dust Collection Test RunTo connect a dust collection hose Recommended Adjustments Factory adjustments that should be verifiedBasic Controls OperationsControl Panel Fence Controls Table ControlsCutterhead Brake G9953/G9953ZX/ G9953ZXF Only Stock Inspection Requirements Follow these rules when choosing and joint- ing stock#/22%#4 Squaring Stock Surface Plane on a Thickness PlanerSurface Planning To surface plane the workpiece on the joint- erEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories Dispoz-A-BladeHolder and KnifeEye protection assortment Cleaning Protecting MaintenanceSchedule Fence Assembly Pivot Points LubricationCutterhead Bearing Blocks Table Elevation Gears & LeadscrewBelts Tools Needed QtyTo properly tension the V-belts To replace the V-beltsTroubleshooting ServiceMotor & Electrical Operations Infeed Table Stop Bolt Rotating/Replacing Cutterhead InsertsTo rotate or replace a spiral cutterhead InsertAdjusting/Replacing Cutterhead Knives Air Pressure Torque WrenchTo adjust or replace the knives Checking knife height with aPage Setting Fence Stops Models G9860 & G9860ZXTo set the 90 fence stop To set the 45 fence stopModels G9953, G9953ZX, G9953ZXF Adjusting Table Parallelism Adjusting Outfeed Table ParallelismCZZY Adjusting Infeed Table Parallelism Then make sure the table lock isGZVg AZi Wiring Wiring Safety InstructionsG9860 & G9860ZX Wiring Diagram Shock HazardG9953 & G9953ZX Wiring Diagram G9953ZXF 220V Wiring Diagram G9953ZXF 440V Wiring Diagram G9860/G9860ZX Cabinet Breakdown Parts List PartsCutterhead Breakdown MotorG9860 Cutterhead & Motor Parts List G9860ZX Cutterhead & Motor Parts ListG9860/G9860ZX Fence Breakdown G9860 Fence Parts List G9860ZX Fence Parts ListG9860/G9860ZX Table Breakdown Parts List + && &%G9860/G9860ZX Handwheel Breakdown Parts List G9953/G9953ZX/G9953ZXF Cabinet Breakdown & Parts List Cutterhead BreakdownG9953 Cutterhead Parts List G9953ZX/G9953ZXF Cutterhead Parts ListG9953/G9953ZX/G9953ZXF Breakdown G9953/G9953ZX/G9953ZXF Fence Parts List G9953/G9953ZX/G9953ZXF Table Breakdown G9953/G9953ZX/G9953ZXF Table Parts List G9953/G9953ZX/G9953ZXF Handwheel Breakdown & Parts List G9953ZXF Motor Parts List G9953/G9953ZX Motor Parts ListG9953/G9953ZX/G9953ZXF Motor Breakdown Label Placement Extreme Series Jointer Mfg. Since 9/11 Warranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Order Hours a DAY
Related manuals
Manual 56 pages 43.38 Kb Manual 56 pages 10.1 Kb Manual 56 pages 10.1 Kb Manual 76 pages 30.5 Kb

G9860 specifications

The Grizzly G9859, G9860, G9861, and G9860ZX are an impressive lineup of high-quality, precision-engineered woodworking machines designed for both hobbyists and professional woodworkers. These machines embody Grizzly's commitment to advanced technology and innovative design, making them essential tools in any woodshop.

The G9859 is a versatile horizontal band saw that offers users enhanced cutting capabilities with its powerful motor and robust construction. One of its standout features is the precision-machined guide system, which ensures accurate cuts every time. The saw's adjustable cutting height and width settings allow it to handle a variety of materials, making it ideal for both intricate and large-scale projects. The G9859 also comes equipped with a heavy-duty steel frame that minimizes vibration, promoting smooth operation.

Next in the lineup is the G9860, a remarkable vertical band saw that excels in both performance and user-friendliness. Featuring an oversized cast iron table, the G9860 provides ample workspace for larger projects. The table can be easily adjusted for bevel cuts, making it a versatile choice for woodworkers looking to enhance their skill set. The saw’s integrated light and adjustable blade guards improve visibility and safety while working.

The G9861 is a powerful jointer that offers professional-grade performance. With its quick-adjust infeed and outfeed tables, this machine makes jointing boards a breeze. The G9861 features a helical cutter head, ensuring a cleaner cut and minimizing noise during operation. This feature is particularly beneficial for users looking for a finish quality that stands out in any woodworking project.

Lastly, the G9860ZX combines the features of a table saw and a cabinet saw, catering to users who need both functionalities. Its robust construction, paired with an impressive motor capacity, allows for smooth and efficient cuts. The G9860ZX is designed with a quick-release fence system, making adjustments fast and easy.

Overall, the Grizzly G9859, G9860, G9861, and G9860ZX represent the forefront of woodworking technology. With features that prioritize precision, safety, and ease of use, these machines are excellent additions to any workshop, whether for small projects or large-scale production runs. With Grizzly's reputation for quality, users can trust these models to deliver performance that meets and exceeds expectations in woodworking applications.