Grizzly G9860 owner manual Bevel Cutting, To bevel cut on the jointer

Page 32

Bevel Cutting

The purpose of bevel cutting on the jointer is to cut a specific angle of the workpiece edge (see Figures 44–45.

Your jointer has fence stops that can be set at 90° or 45°. If your operation requires a different angle, the fence can be locked in place anywhere between these angles.

Figure 44. Fence setup for a bevel cut of 45°.

Figure 45. Illustration of bevel cutting results.

-30-

To bevel cut on the jointer:

1.DISCONNECT JOINTER FROM POWER!

2.Make sure you read and follow the Safety Instructions beginning on Page 6 and the Stock Inspection & Requirement rules beginning on Page 26.

3.Verify that the outfeed table height is properly set (refer to Setting Outfeed Table Height on Page 19).

4.Set the depth of cut for your operation and the fence to the required angle.

Note: We suggest 1⁄16"–1⁄8" depth of cut for bevel cutting, and a more shallow depth for hardwood species or for wide stock.

5.If your workpiece is cupped or warped, place it so the concave side is face down on the infeed table.

6.Connect the jointer to power and turn it ON.

7.With a push block in each hand, press the workpiece against the infeed table and the fence with firm pressure, then feed the workpiece over the cutterhead.

Note: When your leading hand comes within 4" of the cutterhead, lift that push block up and place it on the workpiece portion that is on the outfeed table. Now, focus the down- ward pressure with the leading hand while feeding, then repeat the same action with your trailing hand when it comes within 4" of the cutterhead. Keep your hands safe! DO NOT allow them to get any closer than 4" to the cutterhead.

8.Repeat Step 7 until the bevel cut is satisfac- tory.

Extreme Series Jointer (Mfg. Since 9/11)

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Extreme Series Jointer Ss ,EAD from Leadbased PAINTS Table of Contents Warranty and Returns Machine Description IntroductionManual Accuracy Contact Info Identification Model Specification Comparison Safety Safety Instructions for MachineryChildren & BYSTANDERS. @ZZe XaYgZc ZghWZXdbZVYhigVXidc#Additional Safety Instructions for Jointers Power Supply AvailabilityFull-Load Current Rating Circuit InformationG9953ZXF Circuit Requirements for 440V Operation Circuit Requirements For G9953 G9953ZXG9953ZXF Circuit Requirements for 220V Operation Model G9953ZXF 440V Conversion Grounding RequirementsExtension Cords G9860, G9860ZX, G9953, & G9953ZX Only Replacing Contactor & Overload RelayRewiring Motor Replacing Control Panel Light BulbsSetup Needed for SetupUnpacking Description QtyInventory Clean Up Inventory Figure QtyPlacement Location Site ConsiderationsMounting to Shop Floor Floor LoadMoving & Placing Jointer Using Machine MountsMoving Assembling Jointer Infeed table stop bolt viewed from Underneath the table Step Installing Fence G9860/G960ZXInstalling Fence G9953/G9953ZX/ G9953ZXF Models G9953, G9953ZX, & G9953ZXF Setting OutfeedTo set the outfeed table height Cutter edge at top-dead-center Page To connect a dust collection hose Dust Collection Test RunOFF Button Recommended Adjustments Factory adjustments that should be verifiedControl Panel OperationsBasic Controls Cutterhead Brake G9953/G9953ZX/ G9953ZXF Only Table ControlsFence Controls #/22%#4 Follow these rules when choosing and joint- ing stockStock Inspection Requirements Squaring Stock Surface Plane on a Thickness PlanerSurface Planning To surface plane the workpiece on the joint- erEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories Dispoz-A-BladeHolder and KnifeEye protection assortment Schedule MaintenanceCleaning Protecting Fence Assembly Pivot Points LubricationCutterhead Bearing Blocks Table Elevation Gears & LeadscrewBelts Tools Needed QtyTo properly tension the V-belts To replace the V-beltsMotor & Electrical ServiceTroubleshooting Operations Infeed Table Stop Bolt Rotating/Replacing Cutterhead InsertsTo rotate or replace a spiral cutterhead InsertAdjusting/Replacing Cutterhead Knives Air Pressure Torque WrenchTo adjust or replace the knives Checking knife height with aPage Setting Fence Stops Models G9860 & G9860ZXTo set the 90 fence stop To set the 45 fence stopModels G9953, G9953ZX, G9953ZXF Adjusting Table Parallelism Adjusting Outfeed Table ParallelismCZZY Adjusting Infeed Table Parallelism Then make sure the table lock isGZVg AZi Wiring Wiring Safety InstructionsG9860 & G9860ZX Wiring Diagram Shock HazardG9953 & G9953ZX Wiring Diagram G9953ZXF 220V Wiring Diagram G9953ZXF 440V Wiring Diagram G9860/G9860ZX Cabinet Breakdown Parts List PartsCutterhead Breakdown MotorG9860 Cutterhead & Motor Parts List G9860ZX Cutterhead & Motor Parts ListG9860/G9860ZX Fence Breakdown G9860 Fence Parts List G9860ZX Fence Parts ListG9860/G9860ZX Table Breakdown Parts List + && &%G9860/G9860ZX Handwheel Breakdown Parts List G9953/G9953ZX/G9953ZXF Cabinet Breakdown & Parts List Cutterhead BreakdownG9953 Cutterhead Parts List G9953ZX/G9953ZXF Cutterhead Parts ListG9953/G9953ZX/G9953ZXF Breakdown G9953/G9953ZX/G9953ZXF Fence Parts List G9953/G9953ZX/G9953ZXF Table Breakdown G9953/G9953ZX/G9953ZXF Table Parts List G9953/G9953ZX/G9953ZXF Handwheel Breakdown & Parts List G9953/G9953ZX/G9953ZXF Motor Breakdown G9953/G9953ZX Motor Parts ListG9953ZXF Motor Parts List Label Placement Extreme Series Jointer Mfg. Since 9/11 Warranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Order Hours a DAY
Related manuals
Manual 56 pages 43.38 Kb Manual 56 pages 10.1 Kb Manual 56 pages 10.1 Kb Manual 76 pages 30.5 Kb

G9860 specifications

The Grizzly G9859, G9860, G9861, and G9860ZX are an impressive lineup of high-quality, precision-engineered woodworking machines designed for both hobbyists and professional woodworkers. These machines embody Grizzly's commitment to advanced technology and innovative design, making them essential tools in any woodshop.

The G9859 is a versatile horizontal band saw that offers users enhanced cutting capabilities with its powerful motor and robust construction. One of its standout features is the precision-machined guide system, which ensures accurate cuts every time. The saw's adjustable cutting height and width settings allow it to handle a variety of materials, making it ideal for both intricate and large-scale projects. The G9859 also comes equipped with a heavy-duty steel frame that minimizes vibration, promoting smooth operation.

Next in the lineup is the G9860, a remarkable vertical band saw that excels in both performance and user-friendliness. Featuring an oversized cast iron table, the G9860 provides ample workspace for larger projects. The table can be easily adjusted for bevel cuts, making it a versatile choice for woodworkers looking to enhance their skill set. The saw’s integrated light and adjustable blade guards improve visibility and safety while working.

The G9861 is a powerful jointer that offers professional-grade performance. With its quick-adjust infeed and outfeed tables, this machine makes jointing boards a breeze. The G9861 features a helical cutter head, ensuring a cleaner cut and minimizing noise during operation. This feature is particularly beneficial for users looking for a finish quality that stands out in any woodworking project.

Lastly, the G9860ZX combines the features of a table saw and a cabinet saw, catering to users who need both functionalities. Its robust construction, paired with an impressive motor capacity, allows for smooth and efficient cuts. The G9860ZX is designed with a quick-release fence system, making adjustments fast and easy.

Overall, the Grizzly G9859, G9860, G9861, and G9860ZX represent the forefront of woodworking technology. With features that prioritize precision, safety, and ease of use, these machines are excellent additions to any workshop, whether for small projects or large-scale production runs. With Grizzly's reputation for quality, users can trust these models to deliver performance that meets and exceeds expectations in woodworking applications.
Top Page Image Contents