Grizzly G0612 owner manual

Page 20

J

I

K

Figure 22. G0612 parts and controls (back

view).

I.Fence Bracket Assembly

J.Fence Tilting Handle

K.Fence Sliding Handle

A.Outfeed Table: Supports the workpiece after it passes over the cutterhead.

B.Cutterhead Guard: Shields the cutterhead to increase operator safety during operation. The cutterhead guard is under spring tension; it will always (unless blocked) snap forward to hit the fence. DO NOT operate the jointer if the guard is not functioning properly.

C.Fence: The fence guides the workpiece uniformly over the cutterhead at the desired angle.

D.Infeed Table: Supports the workpiece as it is pushed over the cutterhead. The height of the infeed table relative to the cutterhead determines the depth of the cut.

E.Depth of Cut Adjustment Knob: This knob lets you change the height of the infeed table and thus control the depth of cut. Best results are achieved when you limit the maximum depth to 1/8" or less when edge jointing and 1/32" when surface planing. You can set the depth of cut precisely with this adjustment knob. To determine the depth of stock the cutterhead will remove from your workpiece, place a straightedge across the outfeed table and use a ruler to measure the gap between the straightedge and the infeed table.

F.ON/OFF Switch: This paddle switch starts and stops the cutterhead rotation. The yellow part of the switch is a safety device. When you remove this yellow key (by pulling it for- ward and out), the switch locks in the OFF position. Always remove this yellow key when you leave the jointer work area. Removing the key prevents unsupervised persons in your shop (especially children) from easily or accidentally starting the jointer.

G/H. Dust Collection Chute and Bag: This assembly receives the debris removed from the workpiece as it is cut. The internal fan

- powered by the jointer motor - pulls the debris away from the cutterhead and blows it through the chute into the bag.

I.Fence Bracket Assembly: The various parts of this assembly let you change the position of the fence relative to the tables and secure it in position during operation.

J.Fence Tilting Handle: Lets you change the angle of the fence and lock it at the angle desired. The fence can be quickly set to 90° (perpendicular to the tables), 45° inward and 45° outward by setting and using the fence stops on the bracket assembly.

K.Fence Sliding Handle: This handle lets you adjust and lock the position of the fence across the tables. ALWAYS firmly tighten the sliding handle before you begin opera- tions. The position of the fence determines the maximum width of the cut as you pass your workpiece over the spinning cutterhead. NEVER operate the jointer if ANY part of cutterhead is exposed on the work area.

-18-

G0612 6" Jointer

Image 20
Contents Model G0612 Jointer Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationSetup Setup Safety UnpackingItems Needed for Setup QtyHardware Not Shown Qty Jointer Box Contents QtyInventory Mounting the Jointer CleanupSite Considerations To attach the fence support Attaching the Fence SupportComponents and Hardware Needed Qty Fence Tilting Handle Installing the FenceTo install the fence To check the outfeed table alignment To adjust the height of the cutterhead knivesChecking Outfeed Table Alignment To Install the dust collection chute and bag Dust CollectionTest Run Attaching the dust collection bagBasic Parts Controls Operation SafetyOperations Page Fence Angle Stops To set the 90º stopAdjusting the inward stop G0612 6 Jointer To set the inward 45º stopTo set the outward 45º stop Stock Inspection Requirements Squaring Stock Surface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories H1298H1300 G7984 H2347 H0736 G3631-Jointer/Planer Knife HoneH1411-PowerHandsSafety Stick Half-mask respirator and disposable Cartridge filtersMaintenance CleaningSchedule BeltsService TroubleshootingPage To replace the fan belt Adjusting/Replacing BeltsTo realign or replace the cutterhead belt Replacing Motor Brushes To replace motor brushesWiring Diagram Parts Breakdown Parts List Safety Label Parts List DescriptionWarranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog