Multiquip MVC98D2 manual Engine Oil Replacement, Air Filter Cleaning, Checking and the V-Belt

Page 22

MAINTENANCE

Engine Oil Replacement

1.Replace engine oil, first in 25 hours of operation and every 50 to 100 hours afterwards.

2.Drain the engine oil when the oil is warm as shown in Figure 17.

Figure 17. Engine Oil (Draining)

3.Remove the oil drain bolt and sealing washer and allow the oil to drain into a suitable container.

4.Replace engine oil in the oil tank with recommended type oil as listed inTable 4.Engine oil capacity is 1.16 quarts (1.1 liter). DO NOT overfill.

5.Install drain bolt with sealing washer and tighten securely.

Air Filter Cleaning

1.Remove the air cleaner cover and foam filter element as shown in Figure 18.

2.Tapthepaperfilterelement(Figure 18)severaltimesonahard surfacetoremovedirt,orblowcompressedair[notexceeding 30psi(207kPa,2.1kgf/cm2)]throughthefilterelementfromthe air cleaner case side.

CAUTION

NEVER brush off dirt. Brushing will force dirt into the fibers and cause poor performance in your air filter.Replace the paper filter element if it is excessively dirty.

3.Clean foam element in warm, soapy water or nonflammable solvent. Rinse and dry thoroughly. Dip the element in clean engine oil and completely squeeze out the excess oil from the element before installing.

Checking and the V-Belt

After 200 hours of operation, remove the belt cover to check theV- belt tension (Figure 19).

1.Remove the belt cover.

2.Tension is proper if the belt bends about 10 mm when depressed strongly with finger between shafts. Loose or worn V-belts reduces power transmission efficiency, causing weak compaction and reduces the life of the belt itself.

Figure 19. Checking V-belt Tension

CAUTION

NEVER attempt to check theV-belt with the engine running. Severe injury can occur if your hand gets caught between the V-belt and the clutch. Always use safetygloves.

Replacing theV-belt

1.Remove the V-belt cover (Figure 20).

2.Using cutters, simply cut the worn or defective V-belt and discard.

3.Place one end of the new V-belt onto the upper pulley (clutch side).

4.Place a 19 mm offset wrench or the like onto the lower vibrator pulley fastening bolt.

5.Place the other end of the V-belt onto lower vibrator pulley. Rotate offset wrench clockwise so that the V-belt moves onto the lower vibrator pulley.

Figure 18. Engine Air Filter

PAGE 22 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model MVC98D2 Engine exhaust and some of its Proposition 65 WarningPage Table of Contents Parts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesGeneral Safety Compactor Safety Fuel Safety Transporting Safety Dimensions MVC98D2 Reversible Plate Compactor DimensionsSpecifications Specifications CompactorGeneral Information Splash plate Counter weightsComponents Water flow from the water tank to the water tubeBasic Engine Engine Controls and ComponentsSetup Installing the Steering HandleBefore Starting TemperatureInspection Engine Oil CheckBelt Check Vibrator Oil CheckStarting the Engine OperationOperation Normal Shut-Down Procedure OPERATION/PREPARATION for LONG-TERM StorageInspection and Maintenance ServiceTables MaintenanceDaily Service Checking and the V-Belt Engine Oil ReplacementAir Filter Cleaning Replacing theV-beltChecking and Replacing the Clutch Checking the Clutch Replacing the ClutchTroubleshooting Engine TroubleshootingPlate Compactor Troubleshooting Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts To 3 UnitsNameplate and Decals Assy Attenzione Atençaõ PrecaucionPart Name QTY Remarks Body Assy Part Name Body Assy Throttle Wire 845 Vibration Assy Vibrating Case Water Tank Assy Sprinkling Pipe Transport Wheel Assy Part Name QTY. Remarks Cylinder Block Assy Cylinder Block Assy Cylinder Head Assy Cylinder Head AIR Cleaner Assy GASKET, AIR Cleaner Muffler Assy Muffler Gasket Crankshaft and Camshaft Assy Camshaft D Assy Piston Assy Includes Items W/# LUB. OIL Pump and Governor Assy LUB. OIL Pump Assy Cooling and Starting Device Assy Cylinder Cover Fuel Injection Pump Assy Fuel Injection Pump Body Fuel Tank and Fuel Line Assy Drain Plug TOOLS, Labels and Gasket SET Assy AIR Cooled Label Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help

MVC98D2 specifications

The Multiquip MVC98D2 is a robust and versatile diesel-powered compactor designed for optimal performance in compacting soil and asphalt in various construction applications. Built with durability in mind, the MVC98D2 is a favored choice among contractors looking for reliable equipment that can withstand the rigors of job sites.

One of the standout features of the MVC98D2 is its advanced vibratory system. This compactor uses a unique dual eccentric weight system, which creates uniform vibration across the entire plate surface. This technology enhances compaction efficiency, allowing operators to achieve maximum density with fewer passes, thus saving time and reducing fuel consumption. The unit's compaction force is complemented by its heavy-duty plate design, which ensures superior performance even in challenging conditions.

Another important characteristic of the MVC98D2 is its powerful and fuel-efficient diesel engine. The model is typically equipped with a dependable engine that provides ample power while minimizing emissions. This makes it not only powerful but also environmentally conscious, adhering to regulatory standards in various regions. The engine is matched with an efficient transmission system that ensures smooth operation and optimal torque delivery.

In addition to its performance features, the MVC98D2 boasts a user-friendly design. The machine’s controls are intuitively arranged, allowing operators to easily and quickly familiarize themselves with its operation. The presence of an adjustable handle enhances comfort, improving operator ergonomics and reducing fatigue during extended use. Safety features, such as an emergency stop button, are also incorporated to enhance workplace safety.

The compact size and weight of the MVC98D2 allow for easy transportation and maneuverability on job sites, making it an excellent choice for both large-scale projects and smaller, confined spaces. The unit is designed to handle a variety of applications including backfill, trenching, and asphalt work, contributing to its versatility across numerous construction needs.

Overall, the Multiquip MVC98D2 stands out for its combination of power, efficiency, and user-friendly features. With its innovative technologies and robust design, it is engineered to deliver superior performance in the toughest conditions, making it a reliable tool for professionals in the construction industry.
Top Page Image Contents