Delta 22-451, 22-450 instruction manual Troubleshooting Maintenance, Adjusting Table Gibs

Page 22

ADJUSTING TABLE GIBS

In the unlikely event of the table developing unwanted movement during planing operations, the table can be checked and adjusted as follows:

1. DISCONNECT MACHINE FROM POWER SOURCE.

2.With the table in the locked position, and with a feeler gage, measure the gap between table gib (A) Fig.

54and table bracket (B). When set correctly the gap should be .005".

3.If an adjustment is necessary, loosen three locknuts (C), and turn three adjustment screws (D) Fig. 54, as necessary to set the correct gap.

4.Check and adjust the gap on the other side of the table in the same manner. Tighten six locknuts, three of which are shown at (C) Fig. 54, after adjustment is made.

A

B

C D

Fig. 54

5.Raise and lower the table to its fullest range and check to see if the table moves up and down without binding.

MACHINE USE

When using your machine, follow these few simple steps for achieving the best results.

1.True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat.

2.Plane to Thickness – Place the side you planed in STEP 1 face down and feed the board through the planer. Plane until this side is flat, then plane both sides of the board until you are satisfied with the thickness. Make thin cuts, and alternate sides with each pass. If, during the planing operation, you notice the board twisting, warping, or bowing, repeat STEP 1 and true up one face.

3.When planing long stock, provide table extensions to support the infeed and outfeed end of the workpiece.

4.Plane with the grain only, and keep planer table clean. Occasionally, wax the table surface to reduce friction during the planing operation.

5.Cross-cut to Final LengthCross-cut lumber to final length.

THE KNIVES ON THE PLANER WILL NOT WEAR EVENLY IF THE WOOD IS FED THROUGH THE SAME SPOT ON THE TABLE EVERY TIME. FEED THE WOOD THROUGH THE PLANER AT DIFFERENT SPOTS ON THE TABLE TO HELP ELIMINATE UNEVEN WEAR OF THE KNIVES.

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

22

Image 22
Contents DC-580 20 Planer Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Additional Specific Safety Rules Failure to Follow These Rules MAY Result in Serious InjuryFunctional Description Power ConnectionsMotor Specifications Grounding InstructionsCarton Contents AssemblyUnpacking and Cleaning Assembling Cutterhead Guard Assembling Dust HoodThree Phase Operation Electrical ConnectionsStarting and Stopping the Planer Locking Switch in OFF PositionOperation Raising and Lowering TableDisconnect Machine from Power Source Feed Roller SpeedsChecking and Adjusting Table Roller Height Table RollersANTI-KICKBACK Fingers Checking and Adjusting Drive Belt Tension Checking and Adjusting Feed Roller Belt Tension CHECKING, Resetting Replacing Knives Constructing Gage Block Adjusting ChipbreakersSetting Knives FA FAdjusting Pressure BAR Adjusting Outfeed RollerAdjusting Infeed Roller Adjusting and Replacing Knives Adjusting Table Height ScaleLeveling the Table Troubleshooting Maintenance Adjusting Table GibsWarranty ServiceAccessories PARTS, Service or Warranty AssistanceCanadian PORTER-CABLE Delta Service Centers

22-451, 22-450 specifications

Delta 22-450 and Delta 22-451 are notable models within Delta's commitment to high-performance, precision woodworking tools. Designed for both amateur and professional woodworkers, these tools embody an ideal blend of innovation, usability, and durability.

One of the primary features of the Delta 22-450 is its powerful motor, which delivers reliable performance even under heavy workloads. This model is equipped with a 1.5 HP motor that ensures consistent power, allowing users to tackle various materials with ease. The motor is designed to operate quietly while minimizing vibrations, which enhances user comfort and precision during operation.

In contrast, the Delta 22-451 takes this a step further, boasting a slightly more robust 1.75 HP motor. This feature allows for increased cutting capacity and the ability to work with thicker and denser materials without bogging down. Both models come with a high-quality build, featuring cast-iron bases that provide stability and reduce vibration, further contributing to accuracy in cuts.

Another standout characteristic of the Delta 22-450 and 22-451 is their innovative fence system. Both models utilize a patented fence design that is easy to adjust and lock securely in place, providing users with confidence in their cutting precision. This technology makes repetitive cuts simple and accurate, which is invaluable when working on larger projects.

Additionally, safety is a key focus in the design of these tools. Delta has incorporated various safety features, such as blade guards and anti-kickback mechanisms, to protect users during operation. This attention to safety is crucial, especially for those who may be newer to woodworking or those operating in busy environments.

Furthermore, these models also feature a dust collection system that maintains a clean workspace. The integrated ports allow for connection to dust extraction systems, ensuring that the work environment remains clear of debris, which not only keeps the workspace safer but also improves visibility for more accurate work.

In summary, the Delta 22-450 and 22-451 are exceptional tools designed for both professional woodworkers and dedicated hobbyists. With powerful motors, advanced fence systems, robust safety features, and effective dust collection, these models are engineered to enhance the woodworking experience and deliver superior results. Their blend of reliability and innovative technology makes them worthwhile investments for anyone serious about woodworking.