Grizzly G0526 instruction manual Clean Up Site Considerations, Working Clearances

Page 17

Clean Up

Site Considerations

 

 

 

 

 

 

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this protective coating with a sol- vent cleaner or citrus-based degreaser such as GrizzlyÕs G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For opti- mum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Avoid chlo- rine-based solvents as they may damage painted surfaces should they come in contact.

To access the sliding surfaces, remove the fence lock nut (Figure 11) and handle, and remove the fence from the jointer unit.

Fence Lock Nut

Figure 11. Removing the fence lock nut so the

sliding surfaces can be cleaned.

Once the sliding surfaces are clean, reassemble the fence to the jointer with the lock handle on the top and the fence lock nut below the fence sup- port assembly.

Gasoline and petroleum products have low flash points and could explode if used to clean machin- ery. DO NOT use gaso- line or petroleum prod- ucts to clean the machin- ery.

Floor Load

The Model G0526 weighs 247 lbs and has a base footprint of 20" x 60". Most commercial floors are suitable for the machine. Some residential floors may require additional reinforcement to support both the machine and operator.

Working Clearances

Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for the machine. See Figure 12 for the overall dimensions of the Model G0526.

60"

20"

Figure 12. Overall machine dimensions.

Unsupervised children and visitors inside your shop could receive seri- ous personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G0526 6" Jointer

-15-

Image 17
Contents Jointer Page Table Of Contents Service Adjustments Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersCommentary IntroductionAmperage Draw Plug-Type Circuit RequirementsCircuit Breaker Amperage DrawGrounding Rewiring ToCircuit Capacity Extension Cords External Features Machine FeaturesCommon Terms & Definitions Unpacking SET UPAbout This Section Parts Inventory Jointer mounting hardware Bag contents Cutterhead guard bag contents Circle Working Clearances Clean Up Site ConsiderationsTools Needed Beginning Assembly Jointer To StandBelt To install the V-beltDust Port Fence To install the dust portTo attach the fence assembly Cutterhead Guard Belt Guard To install the cutterhead guardTo install the V-belt guard To install the handwheels Pedestal Switch HandwheelsTo install the pedestal switch Factory adjustments that should be verified Start Up Recommended AdjustmentsStock Inspection & Requirements OperationsGeneral Squaring Stock Minimum dimensions For edge jointingIllustration of surface planing results Surface PlaningIllustration of edge jointing results Edge JointingIllustration of bevel cutting results Bevel CuttingIllustration of rabbet cutting effects A few sample joints Rabbet CuttingMaintenance Safety MaintenancePersonal injury Before each use, look for the following condi- tionsCarbide Cutters BeltsLubricationDate Approximate Hours Of Use Maintenance Performed Maintenance LogOutfeed Table Height Service AdjustmentsAbout Service To set the 45˚ inward fence stop Depth-Of-Cut Scale Fence StopsTo set the depth-of-cut scale To set the 45˚ outward fence stop To set the 90˚ fence stopTo set the table gibs Adjusting Gibs Carbide CuttersInstalling or adjusting a carbide cutter Reference Info Aftermarket AccessoriesMachine Data Sheet G0526 6 Jointer Description Fence Spiral Cutterhead 307303 308 309 302 310 312 311A 313 Cabinet Stand Troubleshooting Guide Board has excessive bow or twist along G0526 Wiring Diagram Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog