Grizzly G0526 instruction manual Safety Instructions For Power Tools

Page 5

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substi- tute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful information about NOTICE proper operation of the equipment.

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.NEVER USE IN DANGEROUS ENVIRON- MENT. DO NOT use power tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted.

G0526 6" Jointer

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.NEVER FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. DO NOT force tool or attachment to do a job for which it was not designed.

-3-

Image 5
Contents Jointer Page Table Of Contents Service Adjustments Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersCommentary IntroductionAmperage Draw Plug-Type Circuit RequirementsCircuit Breaker Amperage DrawGrounding Rewiring ToCircuit Capacity Extension Cords External Features Machine FeaturesCommon Terms & Definitions Unpacking SET UPAbout This Section Parts Inventory Jointer mounting hardware Bag contents Cutterhead guard bag contents Circle Working Clearances Clean Up Site ConsiderationsTools Needed Beginning Assembly Jointer To StandBelt To install the V-beltDust Port Fence To install the dust portTo attach the fence assembly Cutterhead Guard Belt Guard To install the cutterhead guardTo install the V-belt guard To install the handwheels Pedestal Switch HandwheelsTo install the pedestal switch Factory adjustments that should be verified Start Up Recommended AdjustmentsStock Inspection & Requirements OperationsGeneral Squaring Stock Minimum dimensions For edge jointingIllustration of surface planing results Surface PlaningIllustration of edge jointing results Edge JointingIllustration of bevel cutting results Bevel CuttingIllustration of rabbet cutting effects A few sample joints Rabbet CuttingMaintenance Safety MaintenancePersonal injury Before each use, look for the following condi- tionsCarbide Cutters BeltsLubricationDate Approximate Hours Of Use Maintenance Performed Maintenance LogOutfeed Table Height Service AdjustmentsAbout Service To set the 45˚ inward fence stop Depth-Of-Cut Scale Fence StopsTo set the depth-of-cut scale To set the 45˚ outward fence stop To set the 90˚ fence stopTo set the table gibs Adjusting Gibs Carbide CuttersInstalling or adjusting a carbide cutter Reference Info Aftermarket AccessoriesMachine Data Sheet G0526 6 Jointer Description Fence Spiral Cutterhead 307303 308 309 302 310 312 311A 313 Cabinet Stand Troubleshooting Guide Board has excessive bow or twist along G0526 Wiring Diagram Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog