Grizzly G0526 instruction manual Cutterhead Guard Belt Guard, To install the cutterhead guard

Page 21

Cutterhead Guard

 

V-Belt Guard

 

 

 

 

 

 

Components and Hardware Needed: Qty

Cutterhead Guard

1

Tools Needed:

 

2.5mm Allen Wrench

1

To install the cutterhead guard:

 

1.Slide the cutterhead guard shaft down through the mounting hole on the table. NoteÑThe guard may not fully seat in the hole initially; however, rotating the guard will allow the shaft to fully seat in the hole.

2.Using a 2.5mm Allen wrench, thread the setscrew through the hole in the forked end of the cutterhead guard shaft (Figure 17). NoteÑThread the setscrew far enough to prevent the guard from being pulled out.

Figure 17. Cutterhead guard setscrew.

3.Raise the fence and rotate the guard one revolution counter-clockwise as it appears from the top. Hold the guard in position.

4.Lower the fence and allow the guard to swing back against the fence.

NOTICE

The cutterhead guard must always return to the closed position whenever it is moved. Repeat steps 1-3 until this occurs.

Components and Hardware Needed: Qty

V-Belt Guard

1

Hex Bolt 5Ú16"-18 x 21Ú2"

1

Flat Washer 5Ú16"

1

Tools Needed:

 

12mm Wrench or Socket

1

To install the V-belt guard:

 

Using a 12mm wrench, secure the V-belt guard over the cutterhead pulley and V-belt with the hex bolt and flat washer (Figure 18).

V-Belt Guard

Figure 18. Correctly installed V-belt guard.

G0526 6" Jointer

-19-

Image 21
Contents Jointer Page Table Of Contents Service Adjustments Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersCommentary IntroductionAmperage Draw Plug-Type Circuit RequirementsCircuit Breaker Amperage DrawRewiring To Circuit Capacity Extension CordsGrounding External Features Machine FeaturesCommon Terms & Definitions SET UP About This Section Parts InventoryUnpacking Jointer mounting hardware Bag contents Cutterhead guard bag contents Circle Working Clearances Clean Up Site ConsiderationsTools Needed Beginning Assembly Jointer To StandBelt To install the V-beltTo install the dust port To attach the fence assemblyDust Port Fence To install the cutterhead guard To install the V-belt guardCutterhead Guard Belt Guard Pedestal Switch Handwheels To install the pedestal switchTo install the handwheels Factory adjustments that should be verified Start Up Recommended AdjustmentsOperations GeneralStock Inspection & Requirements Squaring Stock Minimum dimensions For edge jointingIllustration of surface planing results Surface PlaningIllustration of edge jointing results Edge JointingIllustration of bevel cutting results Bevel CuttingIllustration of rabbet cutting effects A few sample joints Rabbet CuttingMaintenance Safety MaintenancePersonal injury Before each use, look for the following condi- tionsCarbide Cutters BeltsLubricationDate Approximate Hours Of Use Maintenance Performed Maintenance LogService Adjustments About ServiceOutfeed Table Height Depth-Of-Cut Scale Fence Stops To set the depth-of-cut scaleTo set the 45˚ inward fence stop To set the 45˚ outward fence stop To set the 90˚ fence stopAdjusting Gibs Carbide Cutters Installing or adjusting a carbide cutterTo set the table gibs Reference Info Aftermarket AccessoriesMachine Data Sheet G0526 6 Jointer Description Fence Spiral Cutterhead 307303 308 309 302 310 312 311A 313 Cabinet Stand Troubleshooting Guide Board has excessive bow or twist along G0526 Wiring Diagram Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog