Miller Electric 12VS manual Installation, Specifications, Gun Recommendation Table, Power, Weight

Page 18

SECTION 4 − INSTALLATION

4-1. Specifications

	Type of	Welding	Wire Feed	Wire	Input	IP	Max. Wire	Overall
	Type of	Power	Wire Feed	Wire	Welding		Max. Wire
	Input	Power	Speed	Diameter	Welding		Spool		Weight
	Input	Source	Speed	Diameter	Circuit	Rating	Spool	Dimensions	Weight
	Power	Source	Range	Range	Circuit	Rating	Capacity	Dimensions
	Power	Type	Range	Range	Rating		Capacity
		Type			Rating

				*Solid Steel:
		Constant		.023 − .062 in				Length: 21 in
		Constant	50 − 780 ipm	(0.6 − 1.6 mm);				(533 mm)
	Open-Circuit/	Voltage (CV)	50 − 780 ipm	(0.6 − 1.6 mm);	425 Amperes			(533 mm)
	Open-Circuit/	Voltage (CV)	(1.3 − 19.8	Stainless Steel:
	Arc Voltage,	Or Constant	(1.3 − 19.8	Stainless Steel:			45 lb (20.4 kg),	Width: 9 in	35 lb
	Arc Voltage,	Or Constant	mpm)	.023 − .052 in	At 60%	23	45 lb (20.4 kg),	Width: 9 in	35 lb
	14 − 110	Current (CC)	mpm)	.023 − .052 in	At 60%	23	12 in (304 mm)	(229 mm)	(16 kg)
	14 − 110	Current (CC)	Depending On	(0.6 − 1.3 mm);	Duty Cycle		12 in (304 mm)	(229 mm)	(16 kg)
	Volts DC	DC Power	Arc Voltage	Flux Cored:				Height: 15-1/2 in
		Source Only	Arc Voltage	Flux Cored:				Height: 15-1/2 in
		Source Only		.030 − .062 in				(394 mm)
				.030 − .062 in				(394 mm)
				(0.8 − 1.6 mm)

	*Maximum gun length is 10 ft. for solid steel .062 in. wire.

4-2. Gun Recommendation Table

Process	Gun

GMAW − Hard or Corded Wires	Bernard Q - 4015

FCAW − Self-Shielding Wires	FC-1260
	Dura-Flux

Notes

OM-1500-19 Page 14

Image 18

Contents Description OM-1500-19 219 185PProcesses File MIG GmawFrom Miller to You Table of Contents Directives StandardsDecstat1/07 Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion Risque D’INCENDIE OU D’EXPLO- Sion LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-1500-19 Disconnect input plug or power before working on machine − DefinitionsKeep your head out of the fumes Manufacturer’s Rating Label For CE Products Weee Label For Products Sold Within The EUSymbols And Definitions Power − InstallationSpecifications WeightEquipment Connection Diagram Aligning Wire Guide And Drive Rolls Installing And Aligning Wire Guide And Drive RollsInstalling Wire Guide And Drive Rolls Cleaning Drive RollsConnecting Welding Gun And Voltage Sensing Clamp Connecting Shielding GasConnecting Weld Cable Weld Cable SizesInstalling Wire And Adjusting Hub Tension Installing And Threading Welding Wire150 mm Pull and hold wire cut off end Tighten Clockwise Threading Welding WireDisplay Board PC20 DIP Switch Settings − Operation Controls With MetersControls Without Meters Gun Consumables Information Wire Speed Control Settings − Maintenance & Troubleshooting Overload Protection And Thermostat ProtectionThermostat Protection Troubleshooting Communication Error DiagnosticsError Indications Motor Overload ErrorOM-1500-19 − Electrical Diagram Circuit Diagram For Wire Feeder− Parts List 19 20 51 68Diagram Part Marking Description Quantity 207 Front Panel Assembly without Meters Front Panel Assembly with Meters Drive Roll & Wire Guide Kits 2 Drive Roll Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s