Miller Electric 12VS manual Installing And Threading Welding Wire

Page 23

4-9. Installing And Threading Welding Wire

. Hold wire tightly to keep it from unraveling.

3

12

6 in (150 mm)

Pull and hold wire; cut off end.

Tighten

Clockwise

WOOD

Installing Wire And Adjusting Hub Tension:

1Retaining Nut

2Hub Tension Adjustment Knob

Remove retaining ring, and install spool so hub pin fits spool hole. Re- install retaining nut.

Adjust tension knob so only a slight force is needed to turn spool.

Threading Welding Wire:

3Pressure Assembly Adjustment Knob

Lay gun cable out straight.

Open pressure assembly, hold wire tightly, and cut off end. Push wire through guides into gun.

Close and tighten pressure assem- bly. Press jog switch until wire comes out gun.

Feed wire against wooden surface, and tighten knob so wire does not slip.

Cut off wire, and close door.

Ref. 804 005-B

OM-1500-19 Page 19

Image 23

Contents File MIG Gmaw OM-1500-19 219 185PProcesses DescriptionFrom Miller to You Table of Contents Decstat1/07 DirectivesStandards HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-1500-19 Keep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Weee Label For Products Sold Within The EU Manufacturer’s Rating Label For CE ProductsSymbols And Definitions Weight − InstallationSpecifications PowerEquipment Connection Diagram Cleaning Drive Rolls Installing And Aligning Wire Guide And Drive RollsInstalling Wire Guide And Drive Rolls Aligning Wire Guide And Drive RollsConnecting Shielding Gas Connecting Welding Gun And Voltage Sensing ClampWeld Cable Sizes Connecting Weld CableThreading Welding Wire Installing And Threading Welding Wire150 mm Pull and hold wire cut off end Tighten Clockwise Installing Wire And Adjusting Hub TensionDisplay Board PC20 DIP Switch Settings Controls With Meters − OperationControls Without Meters Gun Consumables Information Wire Speed Control Settings Thermostat Protection − Maintenance & TroubleshootingOverload Protection And Thermostat Protection Troubleshooting Motor Overload Error DiagnosticsError Indications Communication ErrorOM-1500-19 Circuit Diagram For Wire Feeder − Electrical Diagram19 20 51 68 − Parts ListDiagram Part Marking Description Quantity 207 Front Panel Assembly without Meters Front Panel Assembly with Meters Drive Roll & Wire Guide Kits 2 Drive Roll Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact