Miller Electric 12VS manual Equipment Connection Diagram

Page 19

4-3. Equipment Connection Diagram

! Turn Off wire feeder and welding power source. Stop

engine on welding generator.

1

!

Use only with CC/CV DC Power Sources.

	10		1	Constant Current (CC) or
				Constant Voltage (CV)
				Welding Power Supply
			2	Weld Cable To Feeder
			3	Ground Cable To Workpiece
			Weld cable and ground cable con-
			nections to power source (DCEN/
			DCEP) are dependant on wire type.
			. Since feeder is not polarity sen-
				sitive, there is no need for an
				electrode polarity switch.
			4	Workpiece
	2		5	Voltage Sensing Clamp
		9	Connect voltage sensing clamp to
	8	9	workpiece.
			workpiece.
			6	Gun
	3		6	Gun
	3		7	Gun Trigger Receptacle
			7	Gun Trigger Receptacle
			8	Wire Feeder
	7		9	Gas Hose
	7		10	Gas Cylinder
			10	Gas Cylinder
			Use of shielding gas is dependant
4			on wire type.
4	5
	5		. Shielding gas pressure not to
			. Shielding gas pressure not to
				exceed 100 psi (689 kPa).
	6			Ref. 804 000-C
				Ref. 804 000-C

Notes

OM-1500-19 Page 15

Image 19

Contents File MIG Gmaw OM-1500-19 219 185PProcesses DescriptionFrom Miller to You Table of Contents Standards DirectivesDecstat1/07 HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1500-19 − Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes Weee Label For Products Sold Within The EU Manufacturer’s Rating Label For CE ProductsSymbols And Definitions Weight − InstallationSpecifications PowerEquipment Connection Diagram Cleaning Drive Rolls Installing And Aligning Wire Guide And Drive RollsInstalling Wire Guide And Drive Rolls Aligning Wire Guide And Drive RollsConnecting Shielding Gas Connecting Welding Gun And Voltage Sensing ClampWeld Cable Sizes Connecting Weld CableThreading Welding Wire Installing And Threading Welding Wire150 mm Pull and hold wire cut off end Tighten Clockwise Installing Wire And Adjusting Hub TensionDisplay Board PC20 DIP Switch Settings Controls With Meters − OperationControls Without Meters Gun Consumables Information Wire Speed Control Settings Overload Protection And Thermostat Protection − Maintenance & TroubleshootingThermostat Protection Troubleshooting Motor Overload Error DiagnosticsError Indications Communication ErrorOM-1500-19 Circuit Diagram For Wire Feeder − Electrical Diagram19 20 51 68 − Parts ListDiagram Part Marking Description Quantity 207 Front Panel Assembly without Meters Front Panel Assembly with Meters Drive Roll & Wire Guide Kits 2 Drive Roll Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact