Miller Electric 12VS manual Parts List, 19 20 51 68

Page 34

SECTION 8 − PARTS LIST

34

	18	33
	18			45
73	26 72	32	71	45
73	26 72	32	71					16
		31				39		16
		31				39		42
		36				42		42
		36				42
		29
								44
49			27
			27	28242322
			26	28242322	41	43 42	41	15
				21 40

30

17

68

37

54

53

55

63 69

70 52

58

59

60

62

57

61

62

35

19 20 25

65 47

46

48

7

8

6

50

38

67	5		13
	5
		66	64
		66

1 (Fig 8-2)

3

2 (Fig 8-3)

9

5168 56

14

11 10

12

4

Ref. 804 007-K

Figure 8-1. Complete Assembly

OM-1500-19 Page 30

Image 34

Contents Description OM-1500-19 219 185PProcesses File MIG GmawFrom Miller to You Table of Contents Standards DirectivesDecstat1/07 Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion Risque D’INCENDIE OU D’EXPLO- Sion LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1500-19 − Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes Manufacturer’s Rating Label For CE Products Weee Label For Products Sold Within The EUSymbols And Definitions Power − InstallationSpecifications WeightEquipment Connection Diagram Aligning Wire Guide And Drive Rolls Installing And Aligning Wire Guide And Drive RollsInstalling Wire Guide And Drive Rolls Cleaning Drive RollsConnecting Welding Gun And Voltage Sensing Clamp Connecting Shielding GasConnecting Weld Cable Weld Cable SizesInstalling Wire And Adjusting Hub Tension Installing And Threading Welding Wire150 mm Pull and hold wire cut off end Tighten Clockwise Threading Welding WireDisplay Board PC20 DIP Switch Settings − Operation Controls With MetersControls Without Meters Gun Consumables Information Wire Speed Control Settings Overload Protection And Thermostat Protection − Maintenance & TroubleshootingThermostat Protection Troubleshooting Communication Error DiagnosticsError Indications Motor Overload ErrorOM-1500-19 − Electrical Diagram Circuit Diagram For Wire Feeder− Parts List 19 20 51 68Diagram Part Marking Description Quantity 207 Front Panel Assembly without Meters Front Panel Assembly with Meters Drive Roll & Wire Guide Kits 2 Drive Roll Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s