Miller Electric 12VS Connecting Welding Gun And Voltage Sensing Clamp, Connecting Shielding Gas

Page 21

4-5. Connecting Welding Gun And Voltage Sensing Clamp

2

1

Internal Side View

3

4

6

! Turn Off wire feeder and welding power source. Stop engine on welding generator.

1Gun Securing Knob

2Gun Block

3Gun Outlet Wire Guide

Loosen knob, insert gun end into block. Position outlet wire guide as close as possible to drive rolls with- out touching. Tighten knob.

4Gun Trigger Plug

5Gun Trigger Receptacle

6Voltage Sensing Clamp

Connect voltage sensing clamp to workpiece.

5

Ref. 804 002-C

4-6. Connecting Shielding Gas

			1	Gas Hose With 5/8-18
				Right-hand Thread Fittings
				(Customer Supplied)
		4	2	Shielding Gas Cylinder
	3	4	. Shielding gas pressure not to
	3	Rear View	. Shielding gas pressure not to
		Rear View		exceed 100 psi (689 kPa).
				exceed 100 psi (689 kPa).
			3	Valve
			4	Flowmeter
			Close valve on cylinder when fin-

ished welding.

2

Tools Needed:	1
Tools Needed:
5/8 in

Ref. 804 003-A

OM-1500-19 Page 17

Image 21

Contents Processes OM-1500-19 219 185PDescription File MIG GmawFrom Miller to You Table of Contents Directives StandardsDecstat1/07 Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-1500-19 Disconnect input plug or power before working on machine − DefinitionsKeep your head out of the fumes Weee Label For Products Sold Within The EU Manufacturer’s Rating Label For CE ProductsSymbols And Definitions Specifications − InstallationPower WeightEquipment Connection Diagram Installing Wire Guide And Drive Rolls Installing And Aligning Wire Guide And Drive RollsAligning Wire Guide And Drive Rolls Cleaning Drive RollsConnecting Shielding Gas Connecting Welding Gun And Voltage Sensing ClampWeld Cable Sizes Connecting Weld Cable150 mm Pull and hold wire cut off end Tighten Clockwise Installing And Threading Welding WireInstalling Wire And Adjusting Hub Tension Threading Welding WireDisplay Board PC20 DIP Switch Settings Controls With Meters − OperationControls Without Meters Gun Consumables Information Wire Speed Control Settings − Maintenance & Troubleshooting Overload Protection And Thermostat ProtectionThermostat Protection Troubleshooting Error Indications DiagnosticsCommunication Error Motor Overload ErrorOM-1500-19 Circuit Diagram For Wire Feeder − Electrical Diagram19 20 51 68 − Parts ListDiagram Part Marking Description Quantity 207 Front Panel Assembly without Meters Front Panel Assembly with Meters Drive Roll & Wire Guide Kits 2 Drive Roll Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s