Miller Electric 301 G manual Servicing Air Cleaner, Oil

Page 35

8-4. Servicing Air Cleaner

oil

YStop engine.

YDo not run engine without air cleaner or with dirty element.

1 Wrapper (Foam Element)

Wash wrapper with soap and water solution. Allow wrapper to air dry completely.

Spread 1 tablespoon SAE 30 oil evenly into wrapper. Squeeze out excess oil.

2 Element

Replace element if damaged, dirty, or oily.

aircleaner3 9/00 − 802 772 / Ref. 185 095-A / S-0759

OM-4411 Page 31

Image 35

Contents Description OM-4411207 283EProcesses From Miller to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageEngine Hazards Compressed Air Hazards Radiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationLES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLE Bruit peut affecter l’ouïe LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures graves’AIR Comprimé peut provoquer des blessures ’EXPLOSION DE LA Batterie peutDES Organes Mobiles peuvent provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieInformation sur les champs électromagnétiques Principales normes de sécurité− Definitions Symbol DefinitionsDescription − SpecificationsWeld, Power, And Engine Specifications Dimensions, Weights, and Operating AnglesGenerator Power Curve Fuel Consumption While Welding And Using Generator Power100% Duty Cycle at 280 Amperes DC/CC Exceeding duty cycle can damage unit and void warrantyDuty Cycle CV/DC MIG Mode Stick And MIG Mode Volt-Ampere CurvesCC/DC Stick Mode DC TIG Mode Volt-Ampere Curves Installing Welding Generator − InstallationFull Gasoline Engine Prestart ChecksOil Charger Activating The Dry Charge Battery If ApplicableDo not overfill battery cells Read and follow all instrucConnect negative − cable last Connecting The BatteryInstalling Exhaust Pipe + −Selecting Weld Cable Sizes Connecting To Weld Output TerminalsSocket Information Remote Receptacle InformationFor wetter weld puddle for mild steel Adjusting Wire MIG Weld Puddle ConsistencyReinstall side panel OM-4411 Tools Needed 7/16Front Panel Controls − Operating Welding GeneratorWeld Output Generator Power OutputDescription Of Front Panel Controls Engine SpeedSwitch Setting Process Output On/Off Control Process SwitchProcess Switch Settings Example Combination Remote Amperage Control Stick Remote Amperage/Voltage ControlCircuit Breaker CB3 Hz Generator Power Receptacles And Circuit Breakers− Operating Auxiliary Equipment 240 V 50 a AC Receptacle RC1AC Receptacle RC3 Variable Frequency Hz Generator Power Receptacle RC3Ceptacle RC3 120 V 20 a Variable FrequencyReceptacle Current Available in Amperes− Maintenance & Troubleshooting Maintenance Label Servicing Optional Spark Arrestor Oil Servicing Air CleanerFull Tools Needed Changing Engine Oil, Oil Filter, And Fuel FilterCircuit Breaker CB5 Overload ProtectionLocated behind front panel Tools Needed Trouble Remedy TroubleshootingWelding Variable Frequency Generator Power Receptacle RC3 Hz Generator Power Receptacles RC1 And RC2Engine Start Your Professional Welding Career Now Circuit Diagram For Welding Generator − Electrical Diagram211 395-C Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment Amperes x Volts = Watts Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Earth ground if supplyingFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleMaterial Thickness Reference Chart − -3 41− -4 Main AssemblyBatt 182367 Panel Front w/Components -1Item Panel Front w/ComponentsPanel, Front w/Components Bracket w/Components Generator -1Item Support ServiceYour distributor also gives Transportation Department Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s