Miller Electric 301 G manual Changing Engine Oil, Oil Filter, And Fuel Filter, Full Tools Needed

Page 36

8-5. Changing Engine Oil, Oil Filter, And Fuel Filter

Full

2

1

Tools Needed:

YStop engine and let cool.

1 Oil Drain Valve

2 Oil Filter

Change engine oil and filter accord- ing to engine manual.

YClose valve and valve cap

before adding oil and run- ning engine.

Fill crankcase with new oil to full mark on dipstick (see Section 8-2).

3Fuel Filter

4Fuel Line

Replace line if cracked or worn. Install new filter. Wipe up any spilled fuel.

Start engine, and check for fuel leaks.

YStop engine, tighten connec- tions as necessary, and wipe up fuel.

3

4

803 127 / S-0842

OM-4411 Page 32

Image 36

Contents OM-4411207 283E ProcessesDescription From Miller to You Table of Contents Options and Accessories Warranty Symbol Usage Arc Welding HazardsEngine Hazards Compressed Air Hazards Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interferenceSignification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peut DES Organes Mobiles peuvent provoquer des blessuresLA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesSymbol Definitions − Definitions− Specifications Weld, Power, And Engine SpecificationsDimensions, Weights, and Operating Angles DescriptionFuel Consumption While Welding And Using Generator Power Generator Power CurveExceeding duty cycle can damage unit and void warranty Duty Cycle100% Duty Cycle at 280 Amperes DC/CC Stick And MIG Mode Volt-Ampere Curves CC/DC Stick ModeCV/DC MIG Mode DC TIG Mode Volt-Ampere Curves − Installation Installing Welding GeneratorEngine Prestart Checks OilFull Gasoline Activating The Dry Charge Battery If Applicable Do not overfill battery cellsRead and follow all instruc ChargerConnecting The Battery Installing Exhaust Pipe+ − Connect negative − cable lastConnecting To Weld Output Terminals Selecting Weld Cable SizesRemote Receptacle Information Socket InformationAdjusting Wire MIG Weld Puddle Consistency Reinstall side panel OM-4411Tools Needed 7/16 For wetter weld puddle for mild steel− Operating Welding Generator Front Panel ControlsGenerator Power Output Description Of Front Panel ControlsEngine Speed Weld OutputProcess Switch Process Switch SettingsSwitch Setting Process Output On/Off Control Remote Amperage/Voltage Control Example Combination Remote Amperage Control StickHz Generator Power Receptacles And Circuit Breakers − Operating Auxiliary Equipment240 V 50 a AC Receptacle RC1 Circuit Breaker CB3Variable Frequency Hz Generator Power Receptacle RC3 Ceptacle RC3120 V 20 a Variable Frequency AC Receptacle RC3Current Available in Amperes Receptacle− Maintenance & Troubleshooting Maintenance Label Servicing Optional Spark Arrestor Servicing Air Cleaner OilChanging Engine Oil, Oil Filter, And Fuel Filter Full Tools NeededOverload Protection Located behind front panel Tools NeededCircuit Breaker CB5 Troubleshooting WeldingTrouble Remedy Hz Generator Power Receptacles RC1 And RC2 Variable Frequency Generator Power Receptacle RC3Engine Start Your Professional Welding Career Now − Electrical Diagram Circuit Diagram For Welding Generator211 395-C − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Amperes x Volts = WattsApproximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesMaterial Thickness Reference Chart Main Assembly − -3 41− -4Batt 182367 Panel Front w/Components Panel Front w/Components -1ItemPanel, Front w/Components Bracket w/Components Generator -1Item Service Your distributor also givesSupport Miller Electric Mfg. Co For assistance in filing or settling claims, contactYour distributor and/or equipment manufacturer’s Transportation Department