Miller Electric OM-494 manual Place optional Polarity switches in Re

Page 25

5-10. Making Dual Operator CV Weld Connections w/ Separate Work Cables

Tools Needed:

3/4 in

Direct Current Electrode Positive (DCEP) connections are shown.

Welder A (Left) Side

Welder B (Right) Side

Note position

of Process

Selector switches.

 

Note position

Note position

 

 

of optional

of optional Po-

 

2

Polarity

larity switch.

2

 

switch.

1

 

 

 

 

3

 

 

 

Ref. 190 377 / 802 292-A

Y Stop engine.

3 Work Cables

If unit has the Polarity switch option, con-

Y Do not exceed machine duty cycle.

 

nect work cables to Work receptacles and

For MIG and FCAW welding Direct Current

wire feeder cables to CV receptacles.

. Use Dual Operator mode for CC and

Electrode Positive (DCEP), connect work

. Place optional Polarity switches in Re-

 

CV welding (see Section 6-1).

cables to Negative (−) terminals and wire

 

verse position when using CV weld re-

 

 

feeder cables to CV terminals.

See Section 5-15for proper cable size.

ceptacles. There is no CV weld output

 

1

Strain Reliefs

For MIG and FCAW Direct Current Elec-

when switch is in Straight position.

. Be sure Process Selector and Polarity

Route cables through strain reliefs.

trode Negative (DCEN), connect work

cables to CV terminals and wire feeder

switches are set correctly. See Section

 

 

2

Wire Feeder Cables

cables to Negative (−) terminals.

6-3.

OM-494 Page 21

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Description ProcessesVisit our website at OM-494191 862P January Dual-Operator Engine Driven Welding GeneratorFrom Miller to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageEngine Hazards Compressed Air Hazards California Proposition 65 Warnings Principal Safety StandardsEMF Information Radiation can cause interference− Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un in- cendie ou une explosionDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresInformation sur les champs électromagnétiques Principales normes de sécurité− Definitions Symbols And DefinitionsWeld, Power, And Engine Specifications − SpecificationsDimensions, Weights, And Operating Angles DescriptionFuel Consumption AC Generator PowerDuty Cycle And Overheating Exceeding duty cycle can damage unit and void warrantyOverheating Reduce Duty Cycle MinutesCC/DC − Dual Mode CC/DC − Single ModeCV/DC Mode Volt-Ampere CurvesInstalling Welding Generator − InstallationDo not overfill battery cells Activating The Dry Charge BatteryRead and follow all instruc ChargerInstalling Exhaust Pipe Connecting The BatteryConnect − Cable Last Top View Tools Needed 1/2Fuel Do not use gasoline. Gaso Line will damage engine Engine Prestart ChecksOil Weld Output Terminals Safety Information For Connecting To Weld Output TerminalsUnexpected Weld Output can cause injury or fire Welder a Left Side Welder B Right SideDo not exceed machine duty cycle Welder a Left SideConnect electrode holder cables to Elec- trode receptacles Stop engine Do not exceed machine duty cycleVerse position when using CV weld re Place optional Polarity switches in ReWhen switch is in Straight position Switches are set correctly. See SectionConnect wire feeder cables to CV recep- tacles Connect wire feeder cables to Negative − terminalsBe sure Process Selector switches are Place optional Polarity switch in Re Making Single Operator CC Weld Connections 150 ft 200 ft 250 ft Selecting Weld Cable Sizes350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Put terminalsAfter installing cylinder, wait at Installing Ether Cylinder Optional Ether Starting AidRemote 14 Receptacle Information Socket InformationDual Operator Operation Remote 14 Receptacle ConnectionsEngine Controls − Operating the Welding GeneratorSee -3for weld control descriptions If light goes on, stop engine and check engine beltWeld Controls See Section Do not switch under load Do not switch under load or with out- put onWeld Control Descriptions See Section CV weld output for MIG is only available− Operating Auxiliary Equipment − Maintenance & TroubleshootingEvery 200 h Every 100 hEvery 250 h Every 500 hMaintenance Label By the warranty Servicing Air CleanerTo clean air filter Do not clean housing with air hoseServicing Fuel And Lubrication Systems Weld/Power 1850 Adjusting Engine SpeedServicing Optional Ether Starting Aid CylinderChecking And Replacing Alternator Belt To adjust belt tensionMax Tools Needed 11/16 Stop engine To check belt tensionResetting Fan Belt Safety Shutdown Reinstall cleanout plug Tools Needed 3/8 Inspecting And Cleaning Optional Spark Arrestor MufflerThermostats TP3 And TP4 Internal − Not Shown Circuit ProtectionWelding TroubleshootingFactory Authorized Service Agent check main rectifier SR3 Factory Authorized Service Agent check main rectifier SR2Repair or replace wire feeder Formers T5 thru T10, and control board PC1 or PC5Engine Generator PowerOM-494 Circuit Diagram For Welding Generator − Electrical Diagrams210 657-A Wetstacking − RUN-IN ProcedureMent damage may occur 4exceed duty cycle or equip- ment damage may occur Run-In Procedure Using Load BankCheck oil level frequently dur Ing run-in add oil if neededProcedure at less than Run-In Procedure Using Resistance GridBank/grid From flammablesHas this symbol − Generator Power GuidelinesSelecting Equipment Grounding Generator To Truck Or Trailer FrameHow Much Power Does Equipment Require? Grounding When Supplying Building SystemsEarth ground if supplying Use ground device as stated Electrical codesApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord Possible311 103 96−SEE -2 101 25−SEE FIG 910 − Parts List4748 57−SEE FIG 78−SEE FIG Item Dia Part Description Quantity Mkgs 189 Front Panel Front Panel -1Item Side Control Panels − Welder B Right Side Shown Side Control Panels -1Item Side Control Panels Generator Rectifier Assembly OM-494 Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s
Top Page Image Contents