Miller Electric 350P manual Connecting Spoolmatic 15A Or 30A Gun

Page 19

.A complete Parts List is available at www.MillerWelds.com

3-8. Connecting Spoolmatic) 15A Or 30A Gun

1 Gun Trigger Plug

Insert plug into receptacle, and tighten threaded collar.

2Weld Cable

3Shielding Gas Hose

Route weld cable and gas hose through opening in front panel.

4 Positive Weld Output Terminal

Connect weld cable to weld output terminal.

2

1

3

2

5 Regulator/Flowmeter

Route shielding gas hose through wire drive compartment, out opening in rear panel, and up to regulator/flowmeter. Connect gas hose to regulator/flowmeter.

5

3

4

Tools Needed:

3/4, 5/8 in

803 568-D

OM-1327 Page 15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Description ProcessesFile MIG Gmaw From Miller to You Table of Contents Warranty HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injureAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésIndique des instructions spécifiques LES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OULE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1327 Duty Cycle And Overheating SpecificationsVolt-Ampere Curve Connecting To Weld Output TerminalsInstalling Welding Gun/Cable Holder Installing Work ClampInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun XR Edge guns prior to serial no Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProBe sure to trim liner to proper extension Changing Polarity Setting Gun Polarity For Wire TypeRear Panel Installing Gas SupplyMin Grounding Conductor Size In AWG Installing Wire Spool and Adjusting Hub TensionElectrical Service Guide Hz Single Phase Hz Three Phase Input VoltageSelecting Input Voltage 200/230/460 Volt Models Only Serial Number And Rating Label Location Selecting a Location And Connecting 3-Phase Input PowerDo not move or operate Unit where it could tip Selection a Location And Connecting 1-Phase Input PowerDisconnect Device Input Power Connections Hold wire tightly to keep It from unraveling Threading Welding Wire For MIG GunFor Aluminum Push-Pull welding Turn welding power source Off Threading Welding Wire Through XR GunsFor XR-A Pistol Gun Jog Mode MIG ModeControls Pulse MIG Gun-On-Demand Pulse MIG Mode Voltage AdjustmentWeld Status MIG Gun-On-DemandWeld Parameters For MIG ChartWeldçêcharts Pulse Mode− Programming MIG Welding ModeARC Length Pulse MIG Welding ModeTimers Crater Fill display can be turned Manual Hot Start Mode Setting Hot Start Aluminum Pulse Only ParametersTwo parameters that will have Setting Crater Fill Recommended Crater Fill Parameters Recommended Crater Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Overheating Routine MaintenanceMaintain more often during severe conditions Measuring Input Capacitor Voltage Grooved drive rolls are re Quired for feeding aluminum wire Changing Drive Roll and Wire Inlet GuideHelp Displays XXXMM 350P Jog XXX Wire Feed SpeedHelp Tip SaveTrouble Remedy TroubleshootingOM-1327 − Electrical Diagram 246 030-B Drive Roll And Wire Guide Kits − Parts ListSupport ServiceMiller Electric Mfg. Co Owner’s Record

350P specifications

The Miller Electric 350P is a highly regarded power source in the world of welding, known for its impressive performance and versatility. This machine is part of the Miller family's long-standing tradition of providing reliable and efficient welding solutions for various applications including construction, manufacturing, and maintenance.

One of the main features of the Miller 350P is its ability to perform both MIG and Pulsed MIG welding. This dual capability allows operators to choose the most suitable welding process for their specific requirements. The machine is equipped with a robust inverter technology, which greatly enhances its efficiency and reduces energy consumption. The inverter design allows for a portable and lightweight unit, making it easier for welders to transport and set up in different working environments.

The 350P showcases an intuitive interface, featuring a digital display that provides real-time information on parameters such as voltage, current, and wire feed speed. This advanced interface is user-friendly, allowing operators to make quick adjustments on the fly, ultimately improving productivity and weld quality. The machine also supports a wide range of materials, including steel, stainless steel, and aluminum, making it a versatile tool for various projects.

Another key characteristic of the Miller 350P is its advanced arc control technology. This includes features such as Auto-Set and Adaptive Hot Start, which automatically adjust the welding parameters based on the material thickness and type. This technology not only simplifies the process for the operator but also enhances the overall quality of the welds, reducing the risks of defects and ensuring consistent results.

Additionally, the Miller 350P is designed with durability in mind. The machine is housed in a rugged case that protects it from challenging environments, allowing it to withstand the rigors of everyday use. Its cooling system ensures that it operates at optimal temperatures, preventing overheating during extended welding sessions.

In summary, the Miller Electric 350P is a powerful and versatile welding machine designed to meet the demands of today’s welding professionals. With its advanced technologies, user-friendly interface, and durable construction, it stands out as a top choice for those seeking efficiency and reliability in their welding processes. Whether for industrial applications or personal projects, the 350P offers a robust solution that supports a wide variety of welding needs.
Top Page Image Contents