Miller Electric 350P manual Installing Work Clamp, Installing Welding Gun/Cable Holder

Page 17

.A complete Parts List is available at www.MillerWelds.com

3-5. Installing Work Clamp

1 Work Cable

2 Boot

Route cable through front panel opening. Slide boot onto work cable.

3 Negative (−) Output Terminal

Connect cable to terminal and cover connection with boot.

Close door.

1

2

3

Tools Needed: 3/4 in.

803 540-C

3-6. Installing Welding Gun/Cable Holder

2

3

1Welding Gun/Cable Holder

2Wrapper

3Screw Locations

Remove screws from side panel. Place holder against side panel and align screw holes. Secure holder to side panel with the previously removed screws.

1

Ref. 803 545-D / Ref. 803 539-C

OM-1327 Page 13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents File MIG Gmaw ProcessesDescription From Miller to You Table of Contents Warranty Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can burnARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can injureFalling Equipment can injure Moving Parts can injureCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesIndique des instructions spécifiques Symboles utilisésUNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un incendie ou une explosion LES Pièces Chaudes peuvent provoquer des brûluresLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLes Pièces Mobiles peuvent causer des blessures Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférencesEn ce qui concerne les implants médicaux Principales normes de sécuritéInformations relatives aux CEM OM-1327 Duty Cycle And Overheating SpecificationsVolt-Ampere Curve Connecting To Weld Output TerminalsInstalling Welding Gun/Cable Holder Installing Work ClampInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun Be sure to trim liner to proper extension Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProXR Edge guns prior to serial no Changing Polarity Setting Gun Polarity For Wire TypeRear Panel Installing Gas SupplyElectrical Service Guide Installing Wire Spool and Adjusting Hub TensionHz Single Phase Hz Three Phase Input Voltage Min Grounding Conductor Size In AWGSelecting Input Voltage 200/230/460 Volt Models Only Serial Number And Rating Label Location Selecting a Location And Connecting 3-Phase Input PowerDisconnect Device Input Power Connections Selection a Location And Connecting 1-Phase Input PowerDo not move or operate Unit where it could tip Hold wire tightly to keep It from unraveling Threading Welding Wire For MIG GunFor Aluminum Push-Pull welding For XR-A Pistol Gun Threading Welding Wire Through XR GunsTurn welding power source Off Controls MIG ModeJog Mode Weld Status Pulse MIG Mode Voltage AdjustmentMIG Gun-On-Demand Pulse MIG Gun-On-DemandWeld Parameters For MIG ChartWeldçêcharts Pulse Mode− Programming MIG Welding ModeARC Length Pulse MIG Welding ModeTimers Crater Fill display can be turned Two parameters that will have Setting Hot Start Aluminum Pulse Only ParametersManual Hot Start Mode Setting Crater Fill Recommended Crater Fill Parameters Recommended Crater Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Maintain more often during severe conditions Routine MaintenanceOverheating Measuring Input Capacitor Voltage Grooved drive rolls are re Quired for feeding aluminum wire Changing Drive Roll and Wire Inlet GuideHelp Displays XXXHelp Jog XXX Wire Feed SpeedTip Save MM 350PTrouble Remedy TroubleshootingOM-1327 − Electrical Diagram 246 030-B Drive Roll And Wire Guide Kits − Parts ListSupport ServiceMiller Electric Mfg. Co Owner’s Record

350P specifications

The Miller Electric 350P is a highly regarded power source in the world of welding, known for its impressive performance and versatility. This machine is part of the Miller family's long-standing tradition of providing reliable and efficient welding solutions for various applications including construction, manufacturing, and maintenance.

One of the main features of the Miller 350P is its ability to perform both MIG and Pulsed MIG welding. This dual capability allows operators to choose the most suitable welding process for their specific requirements. The machine is equipped with a robust inverter technology, which greatly enhances its efficiency and reduces energy consumption. The inverter design allows for a portable and lightweight unit, making it easier for welders to transport and set up in different working environments.

The 350P showcases an intuitive interface, featuring a digital display that provides real-time information on parameters such as voltage, current, and wire feed speed. This advanced interface is user-friendly, allowing operators to make quick adjustments on the fly, ultimately improving productivity and weld quality. The machine also supports a wide range of materials, including steel, stainless steel, and aluminum, making it a versatile tool for various projects.

Another key characteristic of the Miller 350P is its advanced arc control technology. This includes features such as Auto-Set and Adaptive Hot Start, which automatically adjust the welding parameters based on the material thickness and type. This technology not only simplifies the process for the operator but also enhances the overall quality of the welds, reducing the risks of defects and ensuring consistent results.

Additionally, the Miller 350P is designed with durability in mind. The machine is housed in a rugged case that protects it from challenging environments, allowing it to withstand the rigors of everyday use. Its cooling system ensures that it operates at optimal temperatures, preventing overheating during extended welding sessions.

In summary, the Miller Electric 350P is a powerful and versatile welding machine designed to meet the demands of today’s welding professionals. With its advanced technologies, user-friendly interface, and durable construction, it stands out as a top choice for those seeking efficiency and reliability in their welding processes. Whether for industrial applications or personal projects, the 350P offers a robust solution that supports a wide variety of welding needs.
Top Page Image Contents