Miller Electric 350P manual Programming, MIG Welding Mode

Page 34

.A complete Parts List is available at www.MillerWelds.com

SECTION 5 − PROGRAMMING

5-1. MIG Welding Mode

1

2

3

4

5

6

8

9

7

Ref. 213 935-A

When the MIG light (2) is illuminated, the unit is in MIG Welding mode.

SETUP

To enter MIG welding mode, depress the SETUP (6) button once to go to GUN selection. Rotate the right knob (9) to select the gun being used. Select MIG for standard

MIG gun, or select XR‐A, EDGE, PYTH alpr for push pull guns, or SPL for spoolgun.

Depress SETUP (6) a second time to illuminate the PROCESS (3) light. Rotate right knob (9) until MIG is displayed (for MIG only units NOT USED will be displayed).

Depress SETUP (6) button again to illuminate the WIRE (4) light. Adjust left knob (8) to select wire type, adjust right knob (9) to select wire size.

Depress SETUP (6) button again to illuminate TIMERS (5) light. For description of the TIMERS, refer to TIMERS menu (see Section 5-3)

If crater fill function menus are enabled, TIMERS light will stay on to allow for adjust- ment of crater parameters and timers (see Section 5-6).

Depress SETUP (6) button again to exit menus and enter MIG welding mode.

OPERATION

Adjust welding Voltage with left knob (8) and Wire Feed Speed with right knob (9). Refer to MIG welding chart for proper Voltage and Wire Feed Speed setting in reference to material type, material thickness, wire, and gas (see Section 4-9).

ARC CONTROL

MIG welding mode: Depress ARC CONTROL (7) button to enter Arc control menu and INDU will appear on the left display and the corresponding setting will appear on the right display. Adjust right knob (9) to adjust inductance setting. In MIG welding mode the Arc control is an inductance control from 0-99. Refer to MIG welding chart for suggested Inductance setting for the wire and gas types being used (see Section 4-9). Changing the inductance will change the fluidity of the puddle.

Low Inductance

High Inductance

Weld Bead

Weld Bead

(0 setting)

99 setting

OM-1327 Page 30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Description ProcessesFile MIG Gmaw From Miller to You Table of Contents Warranty Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can burnWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Equipment can injure Welding Wire can injureFire or Explosion hazard Moving Parts can injureEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésIndique des instructions spécifiques LES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion Risque D’INCENDIE OU LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LE Soudage À L’ARC risque de provoquer des interférencesInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1327 Specifications Duty Cycle And OverheatingConnecting To Weld Output Terminals Volt-Ampere CurveInstalling Work Clamp Installing Welding Gun/Cable HolderInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun XR Edge guns prior to serial no Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProBe sure to trim liner to proper extension Setting Gun Polarity For Wire Type Changing PolarityInstalling Gas Supply Rear PanelHz Single Phase Hz Three Phase Input Voltage Installing Wire Spool and Adjusting Hub TensionElectrical Service Guide Min Grounding Conductor Size In AWGSelecting Input Voltage 200/230/460 Volt Models Only Selecting a Location And Connecting 3-Phase Input Power Serial Number And Rating Label LocationDo not move or operate Unit where it could tip Selection a Location And Connecting 1-Phase Input PowerDisconnect Device Input Power Connections Threading Welding Wire For MIG Gun Hold wire tightly to keep It from unravelingFor Aluminum Push-Pull welding Turn welding power source Off Threading Welding Wire Through XR GunsFor XR-A Pistol Gun Jog Mode MIG ModeControls MIG Gun-On-Demand Pulse MIG Mode Voltage AdjustmentWeld Status Pulse MIG Gun-On-DemandMIG Chart Weld Parameters ForPulse Mode WeldçêchartsMIG Welding Mode − ProgrammingPulse MIG Welding Mode ARC LengthTimers Crater Fill display can be turned Manual Hot Start Mode Setting Hot Start Aluminum Pulse Only ParametersTwo parameters that will have Setting Crater Fill Recommended Crater Parameters Recommended Crater Fill Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Overheating Routine MaintenanceMaintain more often during severe conditions Measuring Input Capacitor Voltage Changing Drive Roll and Wire Inlet Guide Grooved drive rolls are re Quired for feeding aluminum wireXXX Help DisplaysTip Save Jog XXX Wire Feed SpeedHelp MM 350PTroubleshooting Trouble RemedyOM-1327 − Electrical Diagram 246 030-B − Parts List Drive Roll And Wire Guide KitsService SupportOwner’s Record Miller Electric Mfg. Co

350P specifications

The Miller Electric 350P is a highly regarded power source in the world of welding, known for its impressive performance and versatility. This machine is part of the Miller family's long-standing tradition of providing reliable and efficient welding solutions for various applications including construction, manufacturing, and maintenance.

One of the main features of the Miller 350P is its ability to perform both MIG and Pulsed MIG welding. This dual capability allows operators to choose the most suitable welding process for their specific requirements. The machine is equipped with a robust inverter technology, which greatly enhances its efficiency and reduces energy consumption. The inverter design allows for a portable and lightweight unit, making it easier for welders to transport and set up in different working environments.

The 350P showcases an intuitive interface, featuring a digital display that provides real-time information on parameters such as voltage, current, and wire feed speed. This advanced interface is user-friendly, allowing operators to make quick adjustments on the fly, ultimately improving productivity and weld quality. The machine also supports a wide range of materials, including steel, stainless steel, and aluminum, making it a versatile tool for various projects.

Another key characteristic of the Miller 350P is its advanced arc control technology. This includes features such as Auto-Set and Adaptive Hot Start, which automatically adjust the welding parameters based on the material thickness and type. This technology not only simplifies the process for the operator but also enhances the overall quality of the welds, reducing the risks of defects and ensuring consistent results.

Additionally, the Miller 350P is designed with durability in mind. The machine is housed in a rugged case that protects it from challenging environments, allowing it to withstand the rigors of everyday use. Its cooling system ensures that it operates at optimal temperatures, preventing overheating during extended welding sessions.

In summary, the Miller Electric 350P is a powerful and versatile welding machine designed to meet the demands of today’s welding professionals. With its advanced technologies, user-friendly interface, and durable construction, it stands out as a top choice for those seeking efficiency and reliability in their welding processes. Whether for industrial applications or personal projects, the 350P offers a robust solution that supports a wide variety of welding needs.
Top Page Image Contents