Miller Electric 350P manual Crater Fill display can be turned

Page 37

.A complete Parts List is available at www.MillerWelds.com

5-4. Arc Times, Arc Starts, Hot Start (Aluminum Pulse Only), And Crater Fill

.Accessing the Arc Times, Arc Starts, Hot Start (aluminum pulse only), and Crater Fill data will also allow

access to Software Version data and Motor Calibration function. The software version data and motor calibration function are for use by factory authorized service personnel only.

Do not use the motor calibration function if it appears on the displays.

1

Arc times and number of arc starts are saved in unit memory. To view this information, press both SETUP (1) and ARC CONTROL (2) buttons at the same time.

Left display will initially show arc hours.

Rotate left knob (3) and display will change to show number of arc starts.

3

4

To turn on the Crater Fill display, rotate left

knob (3) until CRTR appears in the left display. The factory default for Crater Fill

display is OFF which appears in the right

display. Rotate the right knob (4) until ON appears in the display.

2

Ref. 213 935-A

.The Crater Fill display can be turned

off after parameters are set in pro- grams, but remember that once crater fill is turned on in any program, it will remain on even though it does not ap- pear in the displays because Crater Fill display is turned off.

To exit this menu, press either the SETUP

(1)or ARC CONTROL (2) button, or press a gun trigger on any welding gun connected to the unit.

OM-1327 Page 33

Image 37
Contents Description ProcessesFile MIG Gmaw From Miller to You Table of Contents Warranty Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can burnARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can injureFalling Equipment can injure Moving Parts can injureCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésIndique des instructions spécifiques LES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLes Pièces Mobiles peuvent causer des blessures Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférencesInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1327 Duty Cycle And Overheating SpecificationsVolt-Ampere Curve Connecting To Weld Output TerminalsInstalling Welding Gun/Cable Holder Installing Work ClampInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun XR Edge guns prior to serial no Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProBe sure to trim liner to proper extension Changing Polarity Setting Gun Polarity For Wire TypeRear Panel Installing Gas SupplyElectrical Service Guide Installing Wire Spool and Adjusting Hub TensionHz Single Phase Hz Three Phase Input Voltage Min Grounding Conductor Size In AWGSelecting Input Voltage 200/230/460 Volt Models Only Serial Number And Rating Label Location Selecting a Location And Connecting 3-Phase Input PowerDo not move or operate Unit where it could tip Selection a Location And Connecting 1-Phase Input PowerDisconnect Device Input Power Connections Hold wire tightly to keep It from unraveling Threading Welding Wire For MIG GunFor Aluminum Push-Pull welding Turn welding power source Off Threading Welding Wire Through XR GunsFor XR-A Pistol Gun Jog Mode MIG ModeControls Weld Status Pulse MIG Mode Voltage AdjustmentMIG Gun-On-Demand Pulse MIG Gun-On-DemandWeld Parameters For MIG ChartWeldçêcharts Pulse Mode− Programming MIG Welding ModeARC Length Pulse MIG Welding ModeTimers Crater Fill display can be turned Manual Hot Start Mode Setting Hot Start Aluminum Pulse Only ParametersTwo parameters that will have Setting Crater Fill Recommended Crater Fill Parameters Recommended Crater Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Overheating Routine MaintenanceMaintain more often during severe conditions Measuring Input Capacitor Voltage Grooved drive rolls are re Quired for feeding aluminum wire Changing Drive Roll and Wire Inlet GuideHelp Displays XXXHelp Jog XXX Wire Feed SpeedTip Save MM 350PTrouble Remedy TroubleshootingOM-1327 − Electrical Diagram 246 030-B Drive Roll And Wire Guide Kits − Parts ListSupport ServiceMiller Electric Mfg. Co Owner’s Record

350P specifications

The Miller Electric 350P is a highly regarded power source in the world of welding, known for its impressive performance and versatility. This machine is part of the Miller family's long-standing tradition of providing reliable and efficient welding solutions for various applications including construction, manufacturing, and maintenance.

One of the main features of the Miller 350P is its ability to perform both MIG and Pulsed MIG welding. This dual capability allows operators to choose the most suitable welding process for their specific requirements. The machine is equipped with a robust inverter technology, which greatly enhances its efficiency and reduces energy consumption. The inverter design allows for a portable and lightweight unit, making it easier for welders to transport and set up in different working environments.

The 350P showcases an intuitive interface, featuring a digital display that provides real-time information on parameters such as voltage, current, and wire feed speed. This advanced interface is user-friendly, allowing operators to make quick adjustments on the fly, ultimately improving productivity and weld quality. The machine also supports a wide range of materials, including steel, stainless steel, and aluminum, making it a versatile tool for various projects.

Another key characteristic of the Miller 350P is its advanced arc control technology. This includes features such as Auto-Set and Adaptive Hot Start, which automatically adjust the welding parameters based on the material thickness and type. This technology not only simplifies the process for the operator but also enhances the overall quality of the welds, reducing the risks of defects and ensuring consistent results.

Additionally, the Miller 350P is designed with durability in mind. The machine is housed in a rugged case that protects it from challenging environments, allowing it to withstand the rigors of everyday use. Its cooling system ensures that it operates at optimal temperatures, preventing overheating during extended welding sessions.

In summary, the Miller Electric 350P is a powerful and versatile welding machine designed to meet the demands of today’s welding professionals. With its advanced technologies, user-friendly interface, and durable construction, it stands out as a top choice for those seeking efficiency and reliability in their welding processes. Whether for industrial applications or personal projects, the 350P offers a robust solution that supports a wide variety of welding needs.