Miller Electric Big Blue 400 KX manual Installation, Installing Welding Generator

Page 22

SECTION 5 − INSTALLATION

5-1. Installing Welding Generator

Movement

YAlways securely fasten weld- ing generator onto transport vehicle or trailer and comply with all DOT and other applica- ble codes.

		Y Always ground		generator
			frame to vehicle frame to pre-
			vent electric shock and static
			electricity hazards.
		Y If unit does not have GFCI re-
	OR		ceptacles, use GFCI-protected
			extension cord.
		. See Section 4-2for lifting eye
			rating.
		. See Section 5-2for mounting
Location			information.
Location		Grounding:
		Grounding:
		1	Equipment Grounding Terminal
			(On Front Panel)
		2 Grounding Cable (Not Supplied)
		3	Metal Vehicle Frame
OR	OR	Connect cable from		equipment
		ground terminal to metal vehicle
		frame. Use #10 AWG or larger insu-
		lated copper wire.

Airflow Clearance

18in

(460 mm)

18 in

18 in(460 mm)

(460 mm)

	18 in	18 in
		(460 mm)
	(460 mm)

Grounding 1

GND/PE	2

Electrically bond generator frame to vehicle frame by metal-to-metal contact.

3Y Bed liners, shipping skids, and some running gears insulate the welding generator from the vehicle frame. Always connect a ground wire from the generator equipment grounding termi- nal to bare metal on the vehicle frame as shown.

install3 6/05 − Ref. 800 652 / Ref. 800 477-A / 803 274

OM-4423 Page 16

Image 22

Contents Description OM-4423 215 178NProcesses File Engine DriveFrom Miller to You Table of Contents − Maintenance & Troubleshooting 8-1. Routine Maintenance Standards DirectivesDecrot6/05 Sound Level Information Decrotsound1/05Symbol Usage Arc Welding HazardsEngine Hazards Compressed Air Hazards EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings Radiation can cause interferenceUN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux LE Bruit peut affecter l’ouïeLE Surchauffement peut endom- mager le moteur électrique ’AIR Comprimé peut provoquer des blessures’EMPLOI Excessif peut LES Étincelles Volantes risquent de provoquer des blessuresPour les moteurs diesel LE Soudage À L’ARC risque de provoquer des interférencesPour les moteurs à essence Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone− 50 h Std − DefinitionsStd Manufacturer’s Rating Label Symbols And Definitions Weld, Power, And Engine Specifications − SpecificationsDimensions, Weights, And Operating Angles TIG Mode Stick ModeMIG Mode Volt-Ampere CurvesFuel Consumption Curve shows typical fuel use under weld or power loadsExceeding duty cycle can damage unit and void warranty Duty Cycle And OverheatingAC Generator Power Curve Ac power curve shows the gen- erator power in amperes− Installation Installing Welding GeneratorMounting Welding Generator Tools Needed 1/2 Installing Exhaust PipeStop engine and let cool Do not overfill battery cells Activating The Dry Charge Battery If ApplicableConnecting The Battery Connect Negative − Cable LastFuel Do not use gasoline. Gasoline will damage engine Coolant Recovery TankEngine Prestart Checks OilMIG and Fcaw Welding Connecting To Weld Output TerminalsStick and TIG Welding Stop engine350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Selecting Weld Cable Sizes150 ft 200 ft 250 ft Stop engine beforeConnecting To Remote 14 Receptacle RC14 SocketFront Panel Controls See Section StopDescription Of Front Panel Controls See Section Process/Contactor Switch On CC/CV Models Process/Contactor Switch SettingsDo not Strike Like a Match Lift-ArcStart ProcedureLift-Arc Start Method Touch Lift-Arc t TIGRemote Voltage/Amperage Control − Operating Auxiliary Equipment Volt Receptacles− Maintenance & Troubleshooting Routine MaintenanceMaintenance Label To clean air filter Servicing Air CleanerBy the warranty Do not clean housing with air hoseStop engine and let cool. Reinstall cleanout plug Inspecting And Cleaning Spark Arrestor MufflerServicing Engine Cooling System Adjusting Engine Speed On Standard Models MaximumTo change oil and filter Servicing Fuel And Lubrication SystemsStop engine and let cool After servicing, start engine To replace primary canister fuel filterPress button to reset breaker Overload ProtectionChecking Generator Brushes Replace Damaged BrushesHelp 20 Display Voltmeter/Ammeter Help DisplaysHelp 25 Display Standard Generator Power TroubleshootingWelding Engine Check for obstructed throttle solenoid − Electrical Diagrams Circuit Diagram For Welding Generator221 499-B Wetstacking − RUN-IN ProcedureWelding Generator Stop engine Do not touch hot exhaust Run-In Procedure Using Load BankProcedure at less than From flammables Do not PerformFrom flammables Run-In Procedure Using Resistance GridBank/grid Do not perform run-inSelecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame Earth ground if supplying Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Amperes x Volts = WattsIndustrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsSingle-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts Amperes− Parts List 103 − −5 104 − −3 96− −2 102 101 10071− −4 3031 5756Dia Part Description Quantity Mkgs Dia Part Description Quantity 213600 Panel, Front w/Components Panel, Front w/Components -1ItemFUEL/HM Control Panel Generator Generator -1ItemRectifier Assembly Wiring Harnesses Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s