Miller Electric Big Blue 400 KX manual Sound Level Information, Decrotsound1/05

Page 6

Declaration of Conformity for

European Community (CE) Products

NOTE

This information is provided for units with CE certification (see rating label on unit).

Manufacturer:

European Contact:

Notified Body:

Miller Electric Mg. Co.

Mr. Danilo Fedolfi,

AV Technology Limited

1635 W. Spencer St.

Managing Director

AVTECH House

Appleton, WI 54914 USA

MILLER Europe S.r.l.

Birdhall Lane

Phone: (920) 734-9821

Via Privata Iseo 6/E

Cheadle Heath

 

20098 San Giuliano

Stockport, Chesire SK30XU

 

Milanese, Italy

 

 

Phone: 39(02)98290-1

 

 

Fax: 39(02)98290203

 

European Contact Signature:

The Manufacturer Declares the:

Big Blue 400 KX

Conforms to Directive:

2000/14/EC, Noise Level of Welding Generators

Effective Date:

7/2004

Sound Level Information

Measured Sound Power Level: 97 dB

Guaranteed Sound Power Level: 98 dB

Sound power level requirements determined by the 30% duty cycle of 400 A, 23 V

Conforming assessment procedure 1 of Annex VI will be followed.

The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.

dec_rotsound_1/05

Image 6
Contents Description OM-4423 215 178NProcesses File Engine DriveFrom Miller to You Table of Contents − Maintenance & Troubleshooting 8-1. Routine Maintenance Directives StandardsDecrot6/05 Sound Level Information Decrotsound1/05Symbol Usage Arc Welding HazardsEngine Hazards Compressed Air Hazards EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings Radiation can cause interferenceUN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux LE Bruit peut affecter l’ouïeLE Surchauffement peut endom- mager le moteur électrique ’AIR Comprimé peut provoquer des blessures’EMPLOI Excessif peut LES Étincelles Volantes risquent de provoquer des blessuresPour les moteurs diesel LE Soudage À L’ARC risque de provoquer des interférencesPour les moteurs à essence Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone− Definitions − 50 h StdStd Manufacturer’s Rating Label Symbols And Definitions − Specifications Weld, Power, And Engine SpecificationsDimensions, Weights, And Operating Angles TIG Mode Stick ModeMIG Mode Volt-Ampere CurvesFuel Consumption Curve shows typical fuel use under weld or power loadsExceeding duty cycle can damage unit and void warranty Duty Cycle And OverheatingAC Generator Power Curve Ac power curve shows the gen- erator power in amperes− Installation Installing Welding GeneratorMounting Welding Generator Installing Exhaust Pipe Tools Needed 1/2Stop engine and let cool Do not overfill battery cells Activating The Dry Charge Battery If ApplicableConnecting The Battery Connect Negative − Cable LastFuel Do not use gasoline. Gasoline will damage engine Coolant Recovery TankEngine Prestart Checks OilMIG and Fcaw Welding Connecting To Weld Output TerminalsStick and TIG Welding Stop engine350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Selecting Weld Cable Sizes150 ft 200 ft 250 ft Stop engine beforeConnecting To Remote 14 Receptacle RC14 SocketFront Panel Controls See Section StopDescription Of Front Panel Controls See Section Process/Contactor Switch On CC/CV Models Process/Contactor Switch SettingsDo not Strike Like a Match Lift-ArcStart ProcedureLift-Arc Start Method Touch Lift-Arc t TIGRemote Voltage/Amperage Control − Operating Auxiliary Equipment Volt Receptacles− Maintenance & Troubleshooting Routine MaintenanceMaintenance Label To clean air filter Servicing Air CleanerBy the warranty Do not clean housing with air hoseInspecting And Cleaning Spark Arrestor Muffler Stop engine and let cool. Reinstall cleanout plugServicing Engine Cooling System Adjusting Engine Speed On Standard Models MaximumTo change oil and filter Servicing Fuel And Lubrication SystemsStop engine and let cool After servicing, start engine To replace primary canister fuel filterPress button to reset breaker Overload ProtectionChecking Generator Brushes Replace Damaged BrushesVoltmeter/Ammeter Help Displays Help 20 DisplayHelp 25 Display Troubleshooting Standard Generator PowerWelding Engine Check for obstructed throttle solenoid − Electrical Diagrams Circuit Diagram For Welding Generator221 499-B − RUN-IN Procedure WetstackingWelding Generator Stop engine Do not touch hot exhaust Run-In Procedure Using Load BankProcedure at less than From flammables Do not PerformFrom flammables Run-In Procedure Using Resistance GridBank/grid Do not perform run-in− Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame Earth ground if supplying Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Amperes x Volts = WattsIndustrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsSingle-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts Amperes− Parts List 103 − −5 104 − −3 96− −2 102 101 10071− −4 3031 5756Dia Part Description Quantity Mkgs Dia Part Description Quantity 213600 Panel, Front w/Components Panel, Front w/Components -1ItemFUEL/HM Control Panel Generator Generator -1ItemRectifier Assembly Wiring Harnesses Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s