ENGLISH
with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:
•Injuries caused by touching any rotating/moving parts.
•Injuries caused when changing any parts, blades or accessories.
•Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.
•Impairment of hearing.
•Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF.)
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must read the instruction manual.
Wear safety glasses or goggles when operating this tool.
Wear ear protection when operating this tool.
Electrical safety
This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.
•If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker
Service Centre in order to avoid a hazard.
Using an extension cable
If an extension cable is requred, use an approved extension cable suitable for the power input of this tool (see technical data). The minimum conductor size is 1.5 mm2. When using a cable reel, always unwind the cable completely.
Also refer to the table below.
| Conductor size (mm2) |
|
| Cable rating (Amperes) |
| ||||||
| 0.75 |
|
|
|
|
| 6 |
|
|
|
|
| 1.00 |
|
|
|
|
| 10 |
|
|
|
|
| 1.50 |
|
|
|
|
| 15 |
|
|
|
|
| 2.50 |
|
|
|
|
| 20 |
|
|
|
|
| 4.00 |
|
|
|
|
| 25 |
|
|
|
|
|
|
|
|
| Cable length (m) |
|
| ||||
|
|
| 7.5 | 15 |
| 25 | 30 | 45 | 60 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
| Voltage | AmperesCable rating (Amperes) |
|
|
|
| |||||
| 0 - 2.0 | 6 | 6 | 6 | 6 | 6 | 6 |
|
| ||
|
| 2.1 | - 3.4 | 6 | 6 | 6 | 6 | 6 | 6 |
|
|
|
| 3.5 | - 5.0 | 6 | 6 | 6 | 6 | 10 | 15 |
|
|
|
| 5.1 | - 7.0 | 10 10 10 10 | 15 | 15 |
|
| |||
|
| 7.1 - 12.0 | 15 15 15 15 | 20 | 20 |
|
| ||||
|
| 12.1 | - 20.0 | 20 20 20 20 | 25 | - |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Features
This tool includes some or all of the following features.
1.Variable speed switch
2.
3.Forward/reverse switch
4.Mode selector
5.Tool holder
6.Side handle
7.Depth stop
Assembly
Warning! Before assembly, make sure that the tool is switched off and unplugged.
Fitting the side handle
•Turn the grip counterclockwise until you can slide the side handle (6) onto the front of the tool.
•Rotate the side handle into the desired position.
•Tighten the side handle by turning the grip clockwise.
6