Freud Tools FT3000VCE Tool Use and Care, Service, Additional Safety Rules for Routers

Page 6

English

4.Tool Use and Care

a)Secure your work. Use clamps or a vise to secure and support the work piece to a stable platform. Securing the work with a clamp or vise frees both hands to operate the tool. Holding the work by hand or against your body is unstable and may lead to loss of control.

b)Do not force tool. The power tool will do the job better and safer at the rate for which it was intended.

c)Use the correct tool for your application. Do not use tools for purposes for which they were not intended.

d)Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Have defective switches replaced by an authorized Freud service center.

e)Disconnect the plug from the power source when not in use, before servicing, and when changing accessories such as blades, bits, and cutters. Such preventive safety measures reduce the risk of starting the tool accidentally and causing personal injury.

f)Store idle tools when not in use. Tools should be stored in a dry, high, or locked-up place and out of the reach of children.

g)Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have repaired by and authorized Freud service center. Inspect extension cords regularly and replace if damaged. Keep handles dry, clean, and free from oil or grease. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

h)Check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully inspected to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, mounting, and other conditions that may affect the operation of the tool. A guard or other part that is damaged should be properly repaired or replaced by an authorized Freud service center unless otherwise indicated elsewhere in this instruction manual.

i)Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used with another tool.

5.Service

a)Tool service must be performed only by an Freud authorized service center. Service or maintenance performed by unqualified personnel could result in a risk of injury.

b)When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

ADDITIONAL SAFETY RULES FOR ROUTERS

•WARNING! Do not rout material containing amianthus. Working with materials containing amianthus/asbestos and/or silica stones produces a dust which is harmful to health. Protect yourself from inhaling this dust, in compliance with regulations on accident prevention.

•Tighten collet nut securely to prevent bit from slipping.

•Provide clearance under work piece for router bit when through-cutting.

•Remove any adjusting key or wrench before turning the power tool on. A wrench or key left attached to a rotating part of the power tool may result in personal injury.

•Never tighten collet nut without a bit installed.

•Avoid "Climb-Cutting" (see applications section) this will increase the chance for loss of control resulting in possible personal injury.

•Do not overreach. Keep footing and balance at all times. This enables better control of the

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents FT3000VCE 31/4 HP Router Operating InstructionsTable of Contents Table DES Matières Tabla DE Contenidos Electrical Safety SafetyGeneral Safety Rules Personal SafetyService Additional Safety Rules for RoutersTool Use and Care Double Insulation Descriptions & Specifications Depth Adjustment KnobFunctional Description Specifications SymbolsAssembly & Operation Prior to OperationEnglish Option Adjusting Depth of Cut Depth Adjustment Knob -FigDepth Stop Turret and Turret Stop Rod Turret Stop Positions Adjust Turret Rod to nearest scale number as shown below Powering the Tool On and Off Mounting Template GuidesOperating Instructions FT3000 Router Speed Dial Settings Variable Speed ControlPlunge Cutting- & Fig Cutting ApplicationsEdge Cutting & Fig Table MountingMaintenance & Inspection MaintenanceAccessories AccessoriesService Locations ServiceNorth American Power Tool Warranty English Toupie 3-1/4 HP FT3000VCE Aire de travail SécuritèConserver CES Instructions Règles Générales DE Sécurité Règles de sécurité en matière d’alimentationUtilisation et maintenance de l’outil Règles DE Sécurité Additionnelles Pour ToupieDouble Isolation Descriptions ET Spécifications Description FonctionnelleSymboles SpécificationsAssemblage ET Utilisation Avant L’UTILISATIONFrançais Les blessures corporelles ou d’endommager l’outil Réglage DE LA Profondeur DE Coupe Molette de réglage de la profondeur FigTourelle de butée de profondeur et tige de butée Fig Tourelle à trois Positions de butée Mise à zéro de la profondeur de coupeFrançais Montage DES Guides Pour Gabarit Instructions D’UTILISATIONMise en marche et arrêt de l’outil Réglage de la vitesse de rotation Diamètre du couteau Tr/min maximumsToupillage en plongée et Fig Applications DE CoupeCoupe des bordures et Fig Montage SUR TableCordon d’alimentation Accessoires Points DE ServiceAccessoires Garantie EN Amérique DU Nord Garantie Limitée DE Cinq ANSRebajadora FT3000VCE de 3-1/4 HP Seguridad Eléctrica Guarde Estas Instrucciones Reglas Generales DE SeguridadArea de trabajo Seguridad PersonalUso de la herramienta y cuidado ServicioReglas DE Seguridad Adicionales Para Fresadoras Doble Insulación Descripción DE Funciones EjeEspecificáciones SímbolosAntes DE Operar Instalación Y Desmontaje DE LA Broca 2 OpcionesOpción Español Español Regulación DE LA Profundidad DE Corte Graduación de la altura del motor a Profundidad ceroEspañol Montaje DE LAS Plantillas Guía Instrucciones DE OperaciónEncendido y apagado de la herramienta Control de velocidad variable RPM MáxCortes con efecto émbolo Figs y Tipos DE CortesCorte de bordes Figs y Montaje EN MesaMantenimiento & Inspección ServícioUbicaciones DE Servício AccesoriosTabla Garantíade Contenidos Pautas a Seguir Para LA Garantía DE FreudEspañol Freud America, Inc U.S. dial Canada dial

FT3000VCE specifications

The Freud Tools FT3000VCE is an exceptional plunge router designed for both amateur woodworkers and seasoned professionals. Known for its reliability and precision, this versatile power tool stands out in the crowded market of woodworking equipment, making it a favorite among DIY enthusiasts and contractors alike.

One of the main features of the FT3000VCE is its powerful 3.0 HP motor. This robust motor provides consistent power, ensuring smooth operation even in tough materials such as hardwoods and laminates. The variable speed control, adjustable from 8,000 to 21,000 RPM, allows users to match the routing speed to the task at hand, whether it’s intricate detail work or heavy stock removal.

Precision is paramount in woodworking, and Freud addresses this with its patented "Soft Start" technology. This feature gradually ramps up the motor speed to reduce sudden jolts, giving users better control and minimizing strain on both the router and the material. Additionally, the electronic feedback system ensures a stable RPM throughout the cut, maintaining performance despite varying load conditions.

The FT3000VCE is built with user comfort in mind. Its ergonomic design includes a balanced body with soft-grip handles, allowing for easier maneuverability and reduced operator fatigue during extended use. The inclusion of a precise depth adjustment system simplifies the process of setting cut depth, while the easy-to-read scale ensures accuracy.

Another noteworthy characteristic is the dual side handles that provide added stability and control, especially during complex routing tasks. The router also features a powerful integrated dust collection system, which helps to maintain a clean working environment by effectively capturing sawdust and debris.

For versatility, the Freud FT3000VCE offers a variety of base options including a fixed base, plunge base, and even a cam-lock system for quick changes between bases. This adaptability allows woodworkers to approach a wide range of projects, from edge profiling to mortising and hollowing.

In summary, the Freud Tools FT3000VCE combines power, precision, and comfort into a single reliable tool that can elevate any woodworking project. With its advanced technologies, ergonomic design, and versatile capabilities, it remains a top choice for those seeking a high-quality plunge router.
Top Page Image Contents