Epson DW621 manual Collets, Controls, Adjusting the Depth of Cut, Electronic Speed Control Dial

Page 6

FIG. 2

PLASTIC CAP

TABS

FIG. 3

SPEED CONTROL

DIAL

FIG. 4

FINE

ADJUSTMENT

KNOB0.

 

QUICK ADJUSTER

PLUNGE LOCK

5/8

3/4

1/2

HANDLE

HEIGHT

 

ADJUSTMENT KNOB

DEPTH STOP

 

LOCKING

 

BOLT

 

collet nut will turn approximately 3/4 of a turn and then become tight again. At this point the bit can’t be removed. Using the same procedure, loosen the nut a second time.This lifts the collet and makes it easy to remove the bit.

NOTE: Your router is equipped with a clear plastic cap over the cutting area. This cap assists with dust extraction. When installing a router bit over 1-1/8" in diameter, ensure the plastic cap is removed or positioned above the cutting portion of the bit (Fig. 2).To remove the cap, push it from the bottom of the router. To re-install the cap, align the tabs (Fig. 2) and snap it into place.

Collets

NEVER TIGHTEN THE COLLET ON THIS TOOL WITHOUT FIRST INSTALLING A ROUTER BIT IN IT. TIGHTENING AN EMPTY COLLET CAN DAMAGE THE COLLET.

To change collet sizes, unscrew the collet assembly, as described above. The collet and the collet nut are connected. Do not attempt to remove the collet from the collet nut.

Controls

ELECTRONIC SPEED CONTROL DIAL

The speed of your router is variable. Use the electronic speed control (Fig. 3) dial to produce uniform cutting results in wood, plastics and aluminum. Use the lower settings (1-3) for large diameter cutters and the higher settings for small diameter cutters. See Table A for more information.

Adjusting the Depth of Cut

QUICK ADJUSTMENT USING RACK AND PINION HEIGHT ADJUSTMENT (FIG. 4)

1)UNPLUG THE ROUTER. It may be necessary to remove the plastic cap before making adjustments.

English

3

Image 6
Contents Page Guide Dutilisation Manual DE Instrucciones General Safety Rules Electrical SafetyWork Area Personal Safety Tool USE and CareService Additional Safety RulesBit Installation and Removal MotorControls Adjusting the Depth of CutCollets Electronic Speed Control DialLock-On/Lock-Off Switch Fig Triple Depth Adjustment Using the Revolver Depth Stop FIGFine Adjustment FIG Dust Collection and Extraction OperationDirection Of Feed To SET the Router for Dust ExtractionFull Warranty MaintenanceAccessories Cleaning & LubricationTable a Aire DE Travail Sécurité ÉlectriqueSécurité DES Personnes Utilisation ET Entretien DES OutilsMesures de sécurité additionnelles RéparationInstallation et retrait des fraises MoteurCommandes Pinces de serrageRéglage de la profondeur de coupe Interrupteur verrouillable fig FonctionnementRéglage DE Précision FIG Dépoussiérage AccessoiresSens d’alimentation Préparation DE LA Toupie Pour LE DépoussiérageNettoyage et lubrification Garantie complèteGarantie DE Satisfaction DE 30 Jours OU Argent Remis Tableau a Reglas generales de seguridad Area DE TrabajoSeguridad Electrica Seguridad Personal USO Y Cuidados DE LA HerramientaReglas adicionales de seguridad ServicioInstalación y remoción de cuchillas Apague Y Desconecte LA RebajadoraBoquillas ControlesAjuste de la profundidad de corte Control Electronico DE VelocidadAjuste Fino FIG Dirección de alimentación Interruptor con seguro de encendido/seguro de apagado FigOperación Recolección y extracción de polvoImportante AccesoriosLimpieza y lubricación Garantía CompletaTabla DE Selección DE Velocidades