Cisco Systems C819GUK9, C819HK9, C819G4GAK9 manual

Page 15

Preface

Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031

Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037

Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Cisco 819 Integrated Services Router Hardware Installation Guide

 

OL-23125-02

13

 

 

 

Image 15
Contents Text Part Number OL-23125-02 Americas HeadquartersPage N T E N T S Connecting a Terminal or PC to the Console Port Contents OL-23125-02 Audience ObjectiveOrganization ConventionsChapter Name Description Warnung Wichtige Sicherheitshinweise Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla SicurezzaPage GEM Disse Anvisninger Page OL-23125-02 Page Searching Cisco Documents Related DocumentationPreface OL-23125-02 General Description Product OverviewWlan LED Cisco 819HG Integrated Services Router3shows the front panel details of the Cisco 819HG ISR 4shows the front panel details of the Cisco 819HGW ISR SKU ID SKU InformationSKU ID Support Description WiFi External AntennaFrequency Band Description ModeHSPA+/HSPA Rebranding of C8xx-B and EHWIC-3G-EVDO-B Hardware FeaturesPlatform Features for Cisco 819 ISRs MB DramGB Dram Snmp AntennasColor Description Power SwitchReset Button LEDsRssi Wlan LED 7describes the 4G LTE LEDs for the Cisco 819 ISR SIM MemoryTwo Internal SIM Card Slots Embedded 3G ModemEmbedded 4G LTE Modem SIM Card3G-ACC-OUT-LA Supported Cisco Antennas and Cables3G-ANTM-OUT-OM 3G-ANTM-OUT-LPAIR-ANT2440NV-R AIR-ANTM2050D-RAIR-ANT2430V-R AIR-ANT5140V-RMaximum Gain Cisco Part Number Description Frequency Ranges Maximum Insertion AIR-CAB005LL-RAIR-CAB020LL-R AIR-CAB050LL-RSerial Port 4G-CAB-ULL-204G-CAB-ULL-50 AC Power Adapter Power SupplyCisco Part Number Accessory AccessoriesOL-23125-02 Installing the Router Equipment, Tools, and Connections Items Shipped with your Router Additional ItemsConnections Ethernet Devices Installing the RouterAccessing the SIM Card Accessing the SIM Cards Installing AntennasInstalling the Antenna Installing a WiFi External AntennaMounting on a Wall Installing on a TableAttaching the Standard Brackets Installing the Router to the Wall Installing a DIN RailTurn the router sideways so that the antenna is at the top Cisco 819 ISR Installed with the DIN Rail Installing the Router Ground ConnectionChassis Ground Connection Using Ring Terminal Installing the Power Cord Retention Lock10 Pre-assemble the O-Ring onto the Barrel 12 Installing Power Cord Lock onto the Router Installing the Power Switch Lock14 Installing Power Switch Lock 16 DC Power Supply Wall-Mounting Features Mounting the DC Power SupplyOL-23125-02 Preventing Damage to the Router Preparing to Connect the RouterConnecting an External Ethernet Switch Connecting a PC, Server, or WorkstationConnecting to an Ethernet Switch Connecting a Terminal or PC to the Console Port Connecting a Terminal or PC to the Console PortTerminal Emulator Settings Connecting a Modem to the Console PortConnecting the DC Adapter Connecting the AC AdapterDC Power Supply PWR1-20W-12VDC and PWR1-20W-24VDC LEDs to Check Normal Patterns Verifying ConnectionsCisco IOS CLI Cisco Configuration Professional ExpressUsername username privilege 15 secret 0 password Enter a hostname for the router this example uses Router Setup Command FacilityConfiguration is displayed Verifying the Initial Configuration OL-23125-02 Router Specifications Technical SpecificationsMaximum Power 11 W 20 W Consumption Transportation/Storage Conditions Martek Railway Power Adapters2 SKUs Mtbf hours Mean Time Between Failure Ground Benign EnvironmentRange 4G LTE SKUs 3GSKUs Supported Power AdaptersC819G+7-K9 C819G-B-K9C819HG-S-K9 C819HGW+7-E-K9 Range 4G LTE SKUs 3G SKUs 3G + WiFi SKUsC819HGW-S-A-K9 C819HG-B-K9 C819HGW-V-A-K9
Related manuals
Manual 196 pages 51.42 Kb