Sanyo KMS2472 Using the Remote Control Unit, ACL button ALL Clear, How to Install Batteries

Page 50

Remote Control Unit (continued)

SENSOR button

When you press this button (use a small-tipped object such as a ballpoint pen),

 

 

 

the

mark will appear at the display. And the room temperature is detected by

 

 

 

the sensor which is built into the indoor unit and the air conditioner is controlled

 

 

 

accordingly.

 

 

 

If the remote control is located near a heat source, such as a space heater or in direct

 

NOTE

 

 

 

 

sunlight, press the SENSOR button to switch to the sensor on the indoor unit.

 

 

 

 

 

 

 

Temperature Display Selector button

This switches the temperature display between °C and °F.

 

 

 

 

Time Display Selector button

This switches the time display between 24-hour time and 12-hour time.

 

 

 

 

ACL button (ALL CLEAR)

Puts the remote control unit into pre-operation status. Always press this button

 

 

 

after replacing the batteries.

 

 

 

 

ADDRESS switch

• The address switch changes to prevent mixing of signals from remote control

 

 

 

 

units when two air conditioners are installed next to each other. Normally, the

 

 

 

 

address switch is set to A. For more information, please contact the dealer

 

 

 

 

where you made the purchase.

 

 

 

• Normally, the tabs on the remote control unit should not be bent.

 

 

 

 

 

NOTE

The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals. If the signal from the remote control unit stops for more than 15 minutes due to the loss of the remote control unit or other trouble, the air conditioner will switch to the temperature sensor which is built into the indoor unit and control the room temperature. In these cases, the temperature around the remote control unit may differ from the temperature detected at the air conditioner’s position.

Using the Remote Control Unit

How to Install Batteries

1. Slide the cover in the direction indicated by the arrow and remove it.

2. Install two AAA alkaline batteries. Make sure the batteries point in the direction marked in the battery compartment.

3. Use a thin object such as the tip of a pen to press the ACL button.

ACL button

NOTE

The batteries last about six months, depending on how much you use the remote control unit. Replace the batteries when the remote control unit’s display fails to light, or when the remote control cannot be used to change the air conditioner’s settings.

Use two fresh leak-proof type-AAA alkaline batteries.

In replacing batteries, follow the instructions as mentioned in the sub- section “How to Install Batteries”.

If you do not use the remote control unit more than 1 month, take out the batteries.

10

OI-807-10-EG

 

Image 50
Contents 11,900BTU / h KMS1272 Capacity Indoor Model No Product Code No 500BTU / h KMS0772000BTU / h KMS0972 17,500BTU / h KMS1872Please Read Before Starting Table of Contents Applicable MULTI-OUTDOOR Units Temperature Indoor Air Intake Temp Outdoor Air Intake Temp Indoor Air Intake Temp Outdoor Air Intake TempUnit Specifications KMS0772208V KMS0972 KMS0972 KMS1272 KMS1272 KMS1872 KMS1872 KMS2472 KMS2472 Major Component Specifications Indoor UnitCB-KMS0972 CB-KMS1272 CB-KMS1872 CB-KMS2472 Resistance k ohm Other Component SpecificationsTemperature F C Dimensional Data KMS0972 KMS1272Indoor Unit KMS1872 KMS2472 Refrigerant Flow Diagram Indoor Unit KMS0772 KMS0972 KMS1272 Indoor unitAir Throw Distance Charts Performance DataIndoor Unit Indoor Unit Indoor Unit Indoor Unit Electric Wiring Diagrams Indoor Unit KMS0772 KMS0972 KMS12728FA2-5257-70500-0 PAM- control Operation FunctionsEmergency operation Timer backup Lamp colorsProtective Functions Freeze preventionPrecautions before Performing Inspection or Repair Method of Self-DiagnosticsIndication on indoor unit Self-diagnostics LampsCode Diagnostics item Blinking On IlluminatedReplace the controller Replace the circuit board or the fuseChecking the indoor unit Control Check items unit operation Using the TEST/T-RUN terminalsChecking the Indoor and Outdoor Units Checking the serial communicationsTrouble Diagnosis of Fan Motor Indoor Fan MotorElectromagnetic interference Noise Malfunction and Electromagnetic InterferenceNoise malfunction Locations most susceptible to noise Trouble CorrectionKMS0772 KMS0972 KMS1272 KMS1872 KMS2472 Features Product Information ContentsAlert Symbols Electrical Requirements Installation LocationSafety Instructions Names of Parts Unit Display and Operation Button Quiet lampRemote Control Unit Display Advance button Remote Control UnitHR. Timer button TransmitterDRY Temperature Display Selector button Using the Remote Control UnitHow to Install Batteries ACL button ALL ClearUsing the Remote Control Unit Operation with the Remote Control Unit OperationOperation with the Remote Control Unit Press the ON/OFF operation buttonCooling and DRY Mode Night Setback Mode is used for saving energyQuiet Mode Clicking sound is heard from the air conditioner Power failure during operationSpecial Remarks Setting the Timer Operation Indication1030 pm 710 am 1100 am Present time Setting the TimerTo cancel a timer program Press the Cancel button Cancellation procedure Using the 1-Hour OFF TimerSetting procedure Operation together with the Daily ON/OFF Repeat TimerHorizontal Adjusting the Airflow DirectionSetting the airflow manually Sweep functionOperation without the Remote Care and CleaningWhen the air conditioner is not running Control UnitHow to replace the anti-mold filter Care and CleaningHow to remove the anti-mold filter Air intake grilleCleaning the negative ion generator How to clean the air clean filterHow to install the air clean filter Washing the grille with waterTrouble Possible Cause Remedy TroubleshootingOperating Range Appendix B Installation Instructions Contents For Indoor Unit…In a Ceiling or Wall For safe installation and trouble-free operation, you mustPlease Read Before Starting …In a RoomGeneral Installation Site Selection Additional Materials Required for InstallationEmbedding the Tubing and Wiring 150 L1+L2+L3+L4 230Make a Hole How to Install the Indoor UnitRemove the Rear Panel from the Unit If Block, Brick, Concrete or Similar Type Wall Install the Rear Panel on the WallIf Wooden Wall Be sure to wear work gloves How to remove the grilleHow to replace the grille Cut by the sharp aluminum finsIndoor unit types KMS1872, KMS2472 Wiring Instructions General precautions on wiring Shape the Indoor Side TubingWiring Instructions for Inter-unit Connections How to connect wiring to the terminal For Indoor Unit Loose wiring may causeFore, be sure all wiring is For Outdoor Unit For solid core wiring or F-cableMounting Right-side tubingDrain cap Switching drain hose and drain capLeft-side tubing To unmount indoor unit Risk of Electric ShockHow to Test Run the Air Conditioner Operation lamp Timer lamp Quiet lamp ION lampRemote Control Unit Installation Position Mounting on a WallAddress Switch Address Setting of the Remote Control UnitConnecting a Home Automation device Installation Check Sheet