Sanyo KMS1872 Loose wiring may cause, Terminal to overheat or result, Unit malfunction. a fire

Page 77

WARNING

Loose wiring may cause the

terminal to overheat or result

 

 

 

in unit malfunction. A fire

 

hazard may also exist. There-

 

fore, be sure all wiring is

 

tightly connected.

When connecting each power wire to the corresponding terminal, follow the instructions “How to connect wiring to the terminal” and fasten the wire securely tight with the fixing screw of the terminal plate.

How to connect wiring to the terminal

a) For Indoor Unit

9/32"

STRIP (7 mm) (ACTUAL

SIZESIZE)

(1)Cut the wire end with a cutting pliers, then strip the insulation to expose the wire about 9/32" (7 mm). See the label (Fig. 28) near the terminal plate.

(2)Using a screwdriver, loosen the terminal screw on the terminal plate.

(3)Insert the wire and tighten the terminal screw com- pletely using a screwdriver.

b) For Outdoor Unit

For solid core wiring (or F-cable)

(1)Cut the wire end with a cutting pliers, then strip the insulation to expose the solid wire about 15/16" (25 mm). (Fig. 29)

(2)Using a screwdriver, remove the terminal screw(s) on the terminal plate.

(3)Using the pliers, bend the solid wire to form a loop suitable for the terminal screw.

(4)Shape the loop wire properly, place it on the termi- nal plate and fix it securely with the removed termi- nal screw using a screwdriver.

For stranded wiring

(1)

Cut the wire end with a cutting pliers, then strip the

 

insulation to expose the stranded wiring about 3/8"

 

(10 mm) and tightly twist the wire ends. (Figs. 30

 

and 31)

(2)

Using a screwdriver, remove the terminal screw(s)

 

on the terminal plate.

(3)

Using a ring connector fastener or pliers, securely

 

clamp each stripped wire end with a ring connector.

 

(Fig. 30)

(4)

Place the ring connector wire, and replace and

 

tighten the removed terminal screw using a screw-

 

driver. (Fig. 32)

Special washer

Wire

Fig. 28

Strip 15/16" (25mm)

Solid wire

Insulation

 

 

Fig. 29

Strip 3/8" (10 mm)

Stranded wire

 

Fig. 30

Twist wire ends

Fig. 31

Screw

Ring connector

Terminal plate

Loop

Ring connector

Screw and special washer

Ring connector

Wire

Fig. 32

12

Image 77
Contents 000BTU / h KMS0972 Capacity Indoor Model No Product Code No 500BTU / h KMS077211,900BTU / h KMS1272 17,500BTU / h KMS1872Please Read Before Starting Table of Contents Applicable MULTI-OUTDOOR Units Indoor Air Intake Temp Outdoor Air Intake Temp Temperature Indoor Air Intake Temp Outdoor Air Intake TempKMS0772 Unit Specifications208V KMS0972 KMS0972 KMS1272 KMS1272 KMS1872 KMS1872 KMS2472 KMS2472 Indoor Unit Major Component SpecificationsCB-KMS0972 CB-KMS1272 CB-KMS1872 CB-KMS2472 Resistance k ohm Other Component SpecificationsTemperature F C KMS0972 KMS1272 Dimensional DataIndoor Unit KMS1872 KMS2472 Indoor Unit KMS0772 KMS0972 KMS1272 Indoor unit Refrigerant Flow DiagramPerformance Data Air Throw Distance ChartsIndoor Unit Indoor Unit Indoor Unit Indoor Unit Indoor Unit KMS0772 KMS0972 KMS1272 Electric Wiring Diagrams8FA2-5257-70500-0 PAM- control Operation FunctionsEmergency operation Lamp colors Timer backupFreeze prevention Protective FunctionsMethod of Self-Diagnostics Precautions before Performing Inspection or RepairCode Diagnostics item Self-diagnostics LampsIndication on indoor unit Blinking On IlluminatedReplace the circuit board or the fuse Replace the controllerChecking the Indoor and Outdoor Units Using the TEST/T-RUN terminalsChecking the indoor unit Control Check items unit operation Checking the serial communicationsIndoor Fan Motor Trouble Diagnosis of Fan MotorNoise malfunction Noise Malfunction and Electromagnetic InterferenceElectromagnetic interference Locations most susceptible to noise Trouble CorrectionKMS0772 KMS0972 KMS1272 KMS1872 KMS2472 Features Product Information ContentsAlert Symbols Electrical Requirements Installation LocationSafety Instructions Names of Parts Quiet lamp Unit Display and Operation ButtonRemote Control Unit Display HR. Timer button Remote Control UnitAdvance button TransmitterDRY How to Install Batteries Using the Remote Control UnitTemperature Display Selector button ACL button ALL ClearUsing the Remote Control Unit Operation Operation with the Remote Control UnitPress the ON/OFF operation button Operation with the Remote Control UnitNight Setback Mode is used for saving energy Cooling and DRY ModeQuiet Mode Clicking sound is heard from the air conditioner Power failure during operationSpecial Remarks Operation Indication Setting the Timer1030 pm 710 am 1100 am Present time Setting the TimerTo cancel a timer program Press the Cancel button Setting procedure Using the 1-Hour OFF TimerCancellation procedure Operation together with the Daily ON/OFF Repeat TimerSetting the airflow manually Adjusting the Airflow DirectionHorizontal Sweep functionWhen the air conditioner is not running Care and CleaningOperation without the Remote Control UnitHow to remove the anti-mold filter Care and CleaningHow to replace the anti-mold filter Air intake grilleHow to install the air clean filter How to clean the air clean filterCleaning the negative ion generator Washing the grille with waterTrouble Possible Cause Remedy TroubleshootingOperating Range Appendix B Installation Instructions For Indoor Unit ContentsPlease Read Before Starting For safe installation and trouble-free operation, you must…In a Ceiling or Wall …In a RoomGeneral Additional Materials Required for Installation Installation Site Selection150 L1+L2+L3+L4 230 Embedding the Tubing and WiringMake a Hole How to Install the Indoor UnitRemove the Rear Panel from the Unit If Block, Brick, Concrete or Similar Type Wall Install the Rear Panel on the WallIf Wooden Wall How to replace the grille How to remove the grilleBe sure to wear work gloves Cut by the sharp aluminum finsIndoor unit types KMS1872, KMS2472 Shape the Indoor Side Tubing Wiring Instructions General precautions on wiringWiring Instructions for Inter-unit Connections Fore, be sure all wiring is Loose wiring may causeHow to connect wiring to the terminal For Indoor Unit For Outdoor Unit For solid core wiring or F-cableRight-side tubing MountingDrain cap Switching drain hose and drain capLeft-side tubing Risk of Electric Shock To unmount indoor unitOperation lamp Timer lamp Quiet lamp ION lamp How to Test Run the Air ConditionerMounting on a Wall Remote Control Unit Installation PositionAddress Setting of the Remote Control Unit Address SwitchInstallation Check Sheet Connecting a Home Automation device