InFocus DS 14DVF instruction manual Important Safety Instructions for Battery Charger

Page 8

English

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

1.This manual contains important safety and operating instructions for battery charger Model UC9SD, UC12SD and UC14SD.

2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

3.To reduce risk of injury, charge HITACHI rechargeable battery type EB1212S and EB1214L for UC12SD and EB1412S and EB1414 for UC14SD. Other type of batteries may burst causing personal injury and damage.

4.Do not expose battery charger to rain or snow.

5.Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

6.To reduce risk of damage to electric plug and cord, pull by plug when disconnecting battery charger.

7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a.That blades of extension cord are the same number, size, and shape as those of plug on battery charger:

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of battery charger as specified in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes*				AWG Size of Cord
AC Input Rating Amperes*				AWG Size of Cord
Equal to or	but less		Length of Cord, Feet (Meter)
Equal to or	but less		Length of Cord, Feet (Meter)
greater than	than	25 (7.5)		50 (15)	100 (30)	150 (45)
0	2	18		18	18	16
2	3	18		18	16	14
3	4	18		18	16	14

*If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example:

1250watts

125 volts = 10 amperes

9.Do not operate battery charger with damaged cord or plug-replace them immediately.

8

Image 8

Contents Variable speed AvertissementAdvertencia Contents ÍndiceImportant Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Carefully handle power toolsNever use a tool which is defective or operating abnormally Important Safety Instructions for Battery Charger English Disposal of the Exhausted Battery Make Them Available to Other Users Owners of this ToolFunctional Description ModelName of Parts Cordless Driver DrillBattery Charger UC12SD and UC14SD Specifications Battery ChargerAssembly and Operation Removal and Installation Method of BatteryApplications Charging MethodInsert the battery to the battery charger Disconnect battery charger from the receptacleRemove the battery from the battery charger Before USEOperation Mounting and dismounting of the bitChange rotation speed Confirm the cap position see FigTightening torque adjustment HOW to Select Tightening Torque Scope and Suggestions for UsesMaintenance and Inspection Accessories Standard AccessoriesOptional ACCESSORIES.....sold separately Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTAvertissement Lire et comprendre toutes les instructions SécuritéConserver CES Instructions Avertissement Règles DE Sécurité Spécifiques ET Symboles Manipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Description Fonctionnelle ModèleNOM DES Parties Perceuse-visseuse à batterieChargeur de batterie UC12SD et UC14SD Chargeur de batterie UC12SD UC14SDMéthode DE Recharge Méthode DE Retrait ET D’INSTALLATION DE LA BatterieUtilisations Recharge Insérer la batterie dans le chargeur de batterieBrancher la fiche du chargeur de batterie dans la prise Avant L’UTILISATION Débrancher le chargeur de batterie de la priseRetirer la batterie du chargeur de batterie PrécautionUtilisation Pose et dépose du foretChangement de vitesse de rotation Vérification de la position du capuchon. Voir FigRéglage du couple de serrage Plage D’UTILISATION ET Suggestions Sélection DU Couple DE SerrageEntretien ET Inspection Accessoires Accessoires StandardAccessoires EN OPTION.....vendus séparément Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónAdvertencia Lea y entienda todas las instrucciones SeguridadGuarde Estas Instrucciones Advertencia Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente 100 150 Español Eliminación DE LAS Baterías Agotadas Descripción Funcional ModeloNomenclatura Taladro atornillador a bateríaCargador de baterías UC12SD y UC14SD Especificaciones Cargador de bateríasMontaje Y Operación AplicacionesMétodo DE Extracción E Instalación DE LA Batería Método DE CargaInserte la batería en el cargador de baterías CargaAntes DE LA Utilización Desconecte el cargador de baterías del tomacorrienteExtraiga la batería del cargador de baterías PrecauciónPrecaucion OperaciónMontaje y desmontaje de la broca Cambio de velocidad de rotación Confirmar la posición de la cubierta Ver la FigAjuste del par de apriete PrecaucionesAlcance Y Sugerencias Para LA Utilización Forma DE Seleccionar EL PAR DE AprieteMantenimiento E Inspección Accessorios Accesorios EstándarAccesorios OPCIONALES.....de venta por separado 10TLRD-N UC14SD Hitachi Koki Canada Co