InFocus DS 14DVF instruction manual Operation, Mounting and dismounting of the bit

Page 17

English

OPERATION

1. Mounting and dismounting of the bit

Tighten

Loosen

Ring Sleeve

Fig. 5

(1)Mounting the bit

Insert a screwdriver bit etc. into the keyless drill chuck. Firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig.5)

NOTE: If the sleeve becomes loose during operation, tighten it further.

The tightening force becomes stronger when the sleeve is tightened.

(2)Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front). (See Fig.5)

CAUTION:

When mounting a bit into the keyless chuck, tighten firmly. If the sleeve is not tight, the bit may slip or fall out, causing injury.

NOTE: Loosening stuck or hard to move sleeves.

Grasp the bit installed in the keyless chuck, in a vise or similar tool.

Set the cap position to “1-11” and turn on the switch. The motor then starts. Finally, rotate the sleeve to the left, and it will loosen.

2.Confirm that the battery is mounted correctly.

3.Check the rotational direction

Triger switch

RL

marks marks

R L

Selector

Button

Fig. 6

The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 6). (The L and R marks are provided on the body.)

◯When the trigger switch is depressed, the tool rotates. When the trigger is released, the tool stops.

◯The rotational speed of the drill can be controlled by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more.

◯When releasing the trigger of the switch, the brake will be applied for immediate stopping.

17

Image 17

Contents Variable speed AvertissementAdvertencia Índice ContentsMeanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Carefully handle power toolsNever use a tool which is defective or operating abnormally Important Safety Instructions for Battery Charger English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryModel Functional DescriptionName of Parts Cordless Driver DrillBattery Charger UC12SD and UC14SD Battery Charger Specifications Removal and Installation Method of Battery Assembly and Operation Applications Charging MethodDisconnect battery charger from the receptacle Insert the battery to the battery chargerBefore USE Remove the battery from the battery chargerMounting and dismounting of the bit OperationConfirm the cap position see Fig Change rotation speedTightening torque adjustment Scope and Suggestions for Uses HOW to Select Tightening TorqueMaintenance and Inspection Standard Accessories AccessoriesOptional ACCESSORIES.....sold separately Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et comprendre toutes les instructions SécuritéConserver CES Instructions Avertissement Règles DE Sécurité Spécifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Modèle Description FonctionnelleNOM DES Parties Perceuse-visseuse à batterieChargeur de batterie UC12SD et UC14SD UC12SD UC14SD Chargeur de batterieMéthode DE Recharge Méthode DE Retrait ET D’INSTALLATION DE LA BatterieUtilisations Recharge Insérer la batterie dans le chargeur de batterieBrancher la fiche du chargeur de batterie dans la prise Débrancher le chargeur de batterie de la prise Avant L’UTILISATIONRetirer la batterie du chargeur de batterie PrécautionPose et dépose du foret UtilisationVérification de la position du capuchon. Voir Fig Changement de vitesse de rotationRéglage du couple de serrage Sélection DU Couple DE Serrage Plage D’UTILISATION ET SuggestionsEntretien ET Inspection Accessoires Standard AccessoiresAccessoires EN OPTION.....vendus séparément Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadAdvertencia Lea y entienda todas las instrucciones SeguridadGuarde Estas Instrucciones Advertencia No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente 100 150 Español Eliminación DE LAS Baterías Agotadas Modelo Descripción FuncionalNomenclatura Taladro atornillador a bateríaCargador de baterías UC12SD y UC14SD Cargador de baterías EspecificacionesAplicaciones Montaje Y OperaciónMétodo DE Extracción E Instalación DE LA Batería Método DE CargaCarga Inserte la batería en el cargador de bateríasDesconecte el cargador de baterías del tomacorriente Antes DE LA UtilizaciónExtraiga la batería del cargador de baterías PrecauciónPrecaucion OperaciónMontaje y desmontaje de la broca Confirmar la posición de la cubierta Ver la Fig Cambio de velocidad de rotaciónPrecauciones Ajuste del par de aprieteForma DE Seleccionar EL PAR DE Apriete Alcance Y Sugerencias Para LA UtilizaciónMantenimiento E Inspección Accesorios Estándar AccessoriosAccesorios OPCIONALES.....de venta por separado 10TLRD-N UC14SD Hitachi Koki Canada Co