InFocus DS 14DVF instruction manual English

Page 9

English

10.Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman.

11.Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12.To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless driver drill. Before using the model UC12SD or UC14SD battery charger, be sure to read all instructions and cautionary statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB1212S AND EB1214L FOR UC12SD AND EB1412S AND EB1414 FOR UC14SD. OTHER TYPES OF BATTERIES MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury. To avoid these injuries:

1.NEVER disassemble the battery.

2.NEVER incinerate the battery, even if it is damaged or is completely worn out. The battery can explode in a fire.

3.NEVER short-circuit the battery.

4.NEVER insert any objects into the battery charger’s air vents. Electric shock or damage to the battery charger may result.

5.NEVER charge outdoors. Keep the battery away from direct sunlight and use only where there is low humidity and good ventilation.

6.NEVER charge when the temperature is below 50°F (10°C) or above 104°F (40°C).

7.NEVER connect two battery chargers together.

8.NEVER insert foreign objects into the hole for the battery or the battery charger.

9.NEVER use a booster transformer when charging.

10.NEVER use an engine generator or DC power to charge.

11.NEVER store the battery or battery charger in places where the temperature may reach or exceed 104°F (40°C).

12.ALWAYS operate charger on standard household electrical power (120 volts). Using the charger on any other voltage may overheat and damage the charger.

13.ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14.ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

9

Image 9

Contents Avertissement AdvertenciaVariable speed Índice ContentsMeanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Carefully handle power tools Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Important Safety Instructions for Battery Charger English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryModel Functional DescriptionName of Parts Cordless Driver DrillBattery Charger UC12SD and UC14SD Battery Charger SpecificationsRemoval and Installation Method of Battery Assembly and OperationApplications Charging MethodDisconnect battery charger from the receptacle Insert the battery to the battery chargerBefore USE Remove the battery from the battery chargerMounting and dismounting of the bit OperationConfirm the cap position see Fig Change rotation speedTightening torque adjustment Scope and Suggestions for Uses HOW to Select Tightening TorqueMaintenance and Inspection Standard Accessories AccessoriesOptional ACCESSORIES.....sold separately Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSécurité Conserver CES InstructionsAvertissement Lire et comprendre toutes les instructions Avertissement Règles DE Sécurité Spécifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Modèle Description FonctionnelleNOM DES Parties Perceuse-visseuse à batterieChargeur de batterie UC12SD et UC14SD UC12SD UC14SD Chargeur de batterieMéthode DE Retrait ET D’INSTALLATION DE LA Batterie UtilisationsMéthode DE Recharge Insérer la batterie dans le chargeur de batterie Brancher la fiche du chargeur de batterie dans la priseRecharge Débrancher le chargeur de batterie de la prise Avant L’UTILISATIONRetirer la batterie du chargeur de batterie PrécautionPose et dépose du foret UtilisationVérification de la position du capuchon. Voir Fig Changement de vitesse de rotationRéglage du couple de serrage Sélection DU Couple DE Serrage Plage D’UTILISATION ET SuggestionsEntretien ET Inspection Accessoires Standard AccessoiresAccessoires EN OPTION.....vendus séparément Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Guarde Estas InstruccionesAdvertencia Lea y entienda todas las instrucciones Advertencia No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente 100 150 Español Eliminación DE LAS Baterías Agotadas Modelo Descripción FuncionalNomenclatura Taladro atornillador a bateríaCargador de baterías UC12SD y UC14SD Cargador de baterías EspecificacionesAplicaciones Montaje Y OperaciónMétodo DE Extracción E Instalación DE LA Batería Método DE CargaCarga Inserte la batería en el cargador de bateríasDesconecte el cargador de baterías del tomacorriente Antes DE LA UtilizaciónExtraiga la batería del cargador de baterías PrecauciónOperación Montaje y desmontaje de la brocaPrecaucion Confirmar la posición de la cubierta Ver la Fig Cambio de velocidad de rotaciónPrecauciones Ajuste del par de aprieteForma DE Seleccionar EL PAR DE Apriete Alcance Y Sugerencias Para LA UtilizaciónMantenimiento E Inspección Accesorios Estándar AccessoriosAccesorios OPCIONALES.....de venta por separado 10TLRD-N UC14SD Hitachi Koki Canada Co