Bosch Power Tools PS40-2A, PS40B Operating Tips, Charging Battery Pack BC430 30 Minute Charger

Page 11

BM 2610958960 06-08 6/10/08 1:47 PM Page 11

CHARGING BATTERY PACK (BC430 30 MINUTE CHARGER)

Plug charger cord into your standard power outlet, then insert battery pack into charger (Fig. 5).

The charger’s green indicator light will begin to “BLINK”. This indicates that the battery is receiving a fast charge. Fast-charging will automatically stop when the battery pack is fully charged.

When the indicator light stops “BLINKING” (and becomes a steady green light) fast charging is complete.

The battery pack may be used even though the light may still be blinking. The light may require more time to stop blinking depending on temperature. When you begin the

charging process of the battery pack, a steady red light could also mean the battery pack is too hot or too cold.

The purpose of the green light is to indicate that the battery pack is fast-charging. It does not indicate the exact point of full charge. The light will stop blinking in less time if the battery pack was not completely discharged.

When charging several batteries in sequence, the charge time may slightly increase.

When the battery pack is fully charged, unplug the charger (unless you're charging another battery pack) and slip the battery pack back into the tool.

BATTERY

PACK

FIG. 5

RED LIGHT

CHARGER

GREEN LIGHT

Operating Tips

You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the operation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause excess friction by sliding over the surface. This can be damaging to both tool and bit.

DRIVING WITH VARIABLE SPEED

The technique is to start slowly, increasing the speed as the screw runs down. Set the screw snugly by slowing to a stop. Prior to driving screws, pilot and clearance holes should be drilled.

Always hold the machine straight on the bolt to be tightened.

The best method to determine the right impacting/tightening duration is by means of a trial. For small screws, the right impacting/tightening duration can be reached in less then 0.5 Sec. Therefore, work with low RPM and switch the machine off immediately when the screw is tight and the impacting sound can be heard.

For screwing larger, longer wood screws into hard material, pre-drilling is the best method.

-11-

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Ver la página Leer antes de usarFor English Version Version française SeePersonal safety General Safety RulesWork area safety Electrical safetyService Power tool use and careBattery tool use and care Safety Rules for Cordless Impact Drivers Battery Care Battery/ChargerLITHIUM-ION Batteries Battery DisposalSymbols Cordless Impact Driver Functional Description and SpecificationsTrigger Switch Operating Instructions Built in Work Light Inserting and Releasing Battery PackBattery Release Tabs Important Charging Notes Charger INDICATORS, Symbols and MeaningDriving with Variable Speed Charging Battery Pack BC430 30 Minute ChargerBattery Pack RED Light Charger Green Light Operating TipsRunning Nuts and Bolts Tightening TorqueTorque build-up depends on the following factors Fastening with ScrewsCleaning MaintenanceAccessories Sécurité personnelle Consignes générales de sécuritéSécurité du lieu de travail Sécurité électriqueEntretien Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles Le plomb provenant des peintures à base de plomb Entretien des piles Chargeur de pilePiles LITHIUM-ION Mise au rebut des pilesNe tentez pas de Symboles BLOC-PILES Description fonctionnelle et spécificationsVisseuse à percussion sans fil Eclairage D’APPOINT Integre Prises DairConsignes de fonctionnement Insertion ET Retrait DU BLOC-PILES Temoins DE CHARGE, Symboles ET SignificationEclairage D’APPOINT Integre Enfoncement À Vitesse Variable Consignes de fonctionnementChargement DU BLOC-PILES Chargeur 30 Minutes BC430 BLOC-PILES Voyant Rouge Vert ChargeurPose DES Écrous ET DES Boulons Fixation ’AIDE DE VIS Couple DE Serrage’augmentation du couple dépend des facteurs suivants Fixation a L’AIDE DE VISNettoyage AccessoiresEntretien Seguridad personal Normas generales de seguridadSeguridad del área de trabajo Seguridad eléctricaServicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías BM 2610958960 06-08 6/10/08 147 PM Cuidado de las baterías Batería/cargadorBaterias DE LITHIUM-ION Eliminación de las bateríasDe Li-ion SímbolosAtornillador de percusión inalámbrico Descripción funcional y especificacionesInstrucciones de funcionamiento Indicadores Y Simbolos DEL Cargador Y SU Significado LUZ DE Trabajo IncorporadaIntroducción Y Suelta DEL Paquete DE Baterías Notas Importantes Para CargarPaquete DE Baterías LUZ Roja LUZ Verde Cargador Consejos de funcionamientoCarga DEL Paquete DE Baterías Cargador DE 30 Minutos BC430 Sujecion CON Tornillos PAR Motor DE AprieteEl aumento de par motor depende de los siguientes factores Limpieza MantenimientoAccesorios ServicioBM 2610958960 06-08 6/10/08 147 PM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools

PS40-2, PS40-2A, PS40B specifications

The Bosch Power Tools PS40B, PS40-2A, and PS40-2 are versatile cordless impact drivers designed to provide exceptional performance and convenience for both professionals and DIY enthusiasts. Renowned for their quality and durability, these tools boast features that make any fastening job easier and more efficient.

One of the standout features of the PS40 series is its compact and lightweight design, allowing users to operate in tight spaces without sacrificing power. With a mere weight of approximately 2.3 pounds, these impact drivers are easy to handle over extended periods, resulting in reduced user fatigue. Furthermore, the tools are equipped with a 1/4-inch hex chuck that enables quick and simple bit changes without needing additional tools, enhancing productivity during tasks.

The PS40B and PS40-2A models are powered by a robust 12-volt lithium-ion battery, offering a good balance between power and battery life. The battery technology features Bosch’s innovative Electronic Cell Protection, which helps to prolong the lifespan of the battery by preventing overheating and overcharging. This feature is complemented by a built-in battery gauge that provides users with real-time information on the charge status, allowing them to plan their work without unexpected interruptions.

Additionally, these impact drivers incorporate a powerful motor with a maximum torque output of up to 1,200 inch-pounds, making them more than capable of tackling stubborn screws and fasteners across various materials. The integrated two-speed transmission allows users to select between high-speed for rapid fastening and low-speed for more controlled driving, providing versatility for different applications.

Another advantage of the Bosch Power Tools PS40 series is their added safety features. The tools include an advanced built-in LED light that illuminates the work area, ensuring visibility even in dimly lit environments. This feature greatly improves accuracy and safety while working on complex projects.

In conclusion, the Bosch Power Tools PS40B, PS40-2A, and PS40-2 are exemplary impact drivers that combine performance, convenience, and innovative technology, making them an essential addition to any toolbox. With their lightweight design, powerful motor, long-lasting battery, and user-friendly features, these tools stand out as reliable choices for tackling a variety of fastening tasks efficiently. Whether you are a professional contractor or a weekend warrior, the PS40 series will meet—and often exceed—your expectations.
Top Page Image Contents