Lexicon MC-1 owner manual Restore Factory Defaults, Equalization, Bass and Treble Level

Page 19

MC-1 Digital Controller

S2ystem Configuration

SystemConfiguration

Restore Factory Defaults

Although the MC-1 memory is cleared before it leaves the factory, it is good practice to restore the factory defaults with the following procedure before system configuration.

Turn the MC-1 OFF with the remote control. Turn the unit back ON and immediately press and hold the MUTE button on the remote. (Make sure you do not block the infrared receiver on the MC-1 front panel.) The display will read:

FACTORY PRESETS MENU

EXIT

RESTORE DEFAULTS

Equalization

MAIN MENU

EFFECT ADJUST

EQUALIZATION

DISPLAY ADJUST

SETUP

Press ▼ to highlight RESTORE DEFAULTS, then press SELECT. This will clear and reload all preset effects and all factory settings of Volume, Balance, Contrast, Configuration, etc. When the message FACTORY DEFAULTS RESTORED is displayed, press DONE to return to normal operation.

In the main menu, press SELECT to open the Equalization menu which contains Bass, Treble and Tilt controls, and a Loudness parameter.

	EQUALIZATION MENU			Adjust with ▲or ▼
	BASS LEVEL	+0.0dB
	BASS LEVEL	+0.0dB		-6.0 to +6.0dB
	TREBLE LEVEL +0.0dB			-6.0 to +6.0dB
	TILT	+0.0dB		-3.0dB to +3.0dB
	LOUDNESS	ON		ON, OFF

Bass and Treble Level

Bass and Treble level controls are provided to compensate for inconsis- tencies in source material, rather than variations in room conditions. The BASS LEVEL control allows a boost or cut of as much as 6dB below 250Hz. The TREBLE LEVEL control allows a boost or cut of 6dB above 1.5kHz. To select either control for adjustment, use ▲ or ▼ to select the control, press SELECT, and use ▲ or ▼ to adjust the setting.

These controls do not affect the sound of rear or side speakers.

11

Image 19

Contents MC-1 Digital Controller Important Safety Instructions Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen Contents Introduction Glossary of Terms Using the DocumentationPage Controls and Indicators InstallationFront Panel Triggers Rear PanelRemote Control InstallationConcert Hall Nightclub Press and hold with Location Considerations ConnectionAC Connections Audio/Video Connections Wiring ConsiderationsAudio/Video Cables Speaker ConnectionsLDD-1 MC-1 ConnectionsDigital Audio Connections Video ConnectionsExpansion Port Input Connections Digital Output AC-3 Ready Laser Disc and LD/DVD PlayersEqualization Restore Factory DefaultsBass and Treble Level Loudness TiltVideo On-Screen Display Display AdjustmentDisplay Adjust Display Adjust MenuDisplay Adjust Menu ON-SCREEN Display Input Gain Analog Inputs Only Input ConfigurationInput Effect FX Assignment Restore Input NameInput Level Meters Input NameAutomatic FX FormatDisc System Configuration AC-3 Only PCM OnlyDTS Only Coax 1-5 and Optical 1-3 Digital Audio Inputs AudioVideo AnalogRecord/Zone 2 Controls Record/ZoneVOL Select and Done remote control onlyDolby, THX, Logic 7, and DTS remote control only CH, Party, TV M, and Music remote control onlyFront L/R Speaker ConfigurationCustom Configuration PGM Trigger AssignmentSides CenterRears Subwoofer Output Setting Output LevelsTHX Configuration Surround EX ConfigurationInternal Noise Test External Noise Test Output Levels MenuLimiter Subwoofer Peak LimiterMute Level Setting Listener PositionPower On Volume Zone 2 Power On VolumeCalibrate Panorama Sync DelayOFF Sync DLY Zone 2 Balance BalanceCustomization Locking SettingsLock Settings Menu Settings Unlocked Custom Name OFF Assign Custom NameCustomizing Effects Using MC-1 EffectsComparing a modified Effect to the factory preset version Main Menu Effect AdjustListening to only the MC-1 Effect Restoring the original parameter values of an EffectNaming your custom Effect Restoring the original Effect namePanorama PCM Effects and Parameters3Nightclub Church PCM Effects and Parameters Concert HallCathedral Channel PCM Effects and Parameters PartyMusic Surround Logic PCM Effects and Parameters Music LogicPro Logic PCM Effects and Parameters TV MatrixTHX Cinema PCM Effect Parameters PCM Effects and Parameters Mono LogicPCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters AC-3 Status Display AC-3 Effects and Parameters4AC-3 Status Music AC-3 Effects and Parameters 2-ChannelDolby Digital AC-3 Effects and Parameters LogicTHX 5.1 Including Surround EX AC-3 Effects and ParametersAC-3 Effect Parameters AC-3 Effects and Parameters AC-3 Effects and Parameters DTS 2-Channel DTS Effects and Parameters5DTS Music DTS Film DTS Effects and Parameters DTS LogicDTS Effect Parameters DTS Effects and Parameters DTS THX Including Surround EXDTS Effects and Parameters Troubleshooting TroubleshootingProblem Possible Cause and Solution Restoring Defaults Troubleshooting Routine MaintenanceSpecifications SpecificationsInputs Installation Worksheet