Lexicon MC-1 Setting Listener Position, Mute Level, Zone 2 Power On Volume, Speaker Distance

Page 36

System Configuration

Lexicon

Be sure the limiter is set to ON before exiting. Press DONE to exit and automatically set the limiter to the level you have selected.

Mute Level

This menu allows you to set the level of attenuation used whenever the MC-1 MUTE function is engaged. In the Output Levels menu, attenu- ation levels of -10dB, -20dB, -30dB, -40dB, and FULL are available.

Power On Volume

This control in the Output Levels menu allows you to select the volume at which the MC-1 will power on. You can choose from a range of -80 to +12dB, or elect to have the system power on at the last level used (LAST LVL).

Zone 2 Power On Volume

This control in the Output Levels menu allows you to select the initial volume level for Zone 2. You can choose from a range of -80 to +12dB, or elect to have Zone 2 power on at the last level used (LAST LVL).

Setting Listener Position

SETUP MENU

INPUT CONFIG

SPEAKER CONFIG

OUTPUT LEVELS

LISTENER POSITION

LOCK SETTINGS

Speaker Distance

The Listener Position menu is used for setting the surround and center delays and calibrating the Panorama effect.

 

LISTENER POSITION

Adjust with or

 

 

 

 

 

SPEAKER DISTANCE

OFF

based on speaker distance

A/V SYNC DLY

Off, 1 to 60ms (30ms in software Version 3)

CALIBRATE PANORAMA

CAL NOISE, SPEAKER ANGLE, LISTENER POS

L/R BALANCE

< >

 

[ L_ _ _ _ _ _R ]

ZONE 2 BALANCE

< >

 

[ L_ _ _ _ _ _R ]

 

 

 

 

 

The Speaker Distance control automatically sets the appropriate time delays for all of the loudspeakers in a system. Although this adjustment is not a substitute for proper speaker placement, it will help to ensure accurate signal arrival times from all channels at the listening position.

To set up Speaker Distance, you must physically measure the distance from the primary listening position to the front baffle of each individual speaker in your system. An easy and accurate way to accomplish this is to have a person sit in the primary listening position, holding the end of a measuring tape, while a second person extends the tape measure to the front baffle of each speaker in turn.

To enter these values, select SPEAKER DISTANCE in the Listener Position menu and press SELECT. Use and to highlight feet or meters and press SELECT. Press SELECT again to highlight NEAR- EST SPKR. Use and to enter the actual distance, then press DONE.

28

Image 36
Contents MC-1 Digital Controller Important Safety Instructions Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen Contents Introduction Using the Documentation Glossary of TermsPage Installation Controls and IndicatorsFront Panel Rear Panel TriggersInstallation Remote ControlConcert Hall Nightclub Press and hold with Connection Location ConsiderationsAC Connections Wiring Considerations Audio/Video CablesSpeaker Connections Audio/Video ConnectionsMC-1 Connections LDD-1Video Connections Digital Audio ConnectionsExpansion Port Input Connections AC-3 Ready Laser Disc and LD/DVD Players Digital OutputRestore Factory Defaults EqualizationBass and Treble Level Tilt LoudnessDisplay Adjustment Display AdjustDisplay Adjust Menu Video On-Screen DisplayDisplay Adjust Menu ON-SCREEN Display Input Configuration Input Gain Analog Inputs OnlyRestore Input Name Input Level MetersInput Name Input Effect FX AssignmentFX Format AutomaticDisc System Configuration PCM Only AC-3 OnlyDTS Only Audio VideoAnalog Coax 1-5 and Optical 1-3 Digital Audio InputsRecord/Zone Record/Zone 2 ControlsSelect and Done remote control only Dolby, THX, Logic 7, and DTS remote control onlyCH, Party, TV M, and Music remote control only VOLSpeaker Configuration Custom ConfigurationPGM Trigger Assignment Front L/RCenter SidesRears Setting Output Levels THX ConfigurationSurround EX Configuration Subwoofer OutputOutput Levels Menu Internal Noise Test External Noise TestSubwoofer Peak Limiter LimiterSetting Listener Position Power On VolumeZone 2 Power On Volume Mute LevelSync Delay Calibrate PanoramaOFF Sync DLY Balance Zone 2 BalanceLocking Settings Lock Settings MenuSettings Unlocked Custom Name OFF Assign Custom Name CustomizationUsing MC-1 Effects Comparing a modified Effect to the factory preset versionMain Menu Effect Adjust Customizing EffectsRestoring the original parameter values of an Effect Naming your custom EffectRestoring the original Effect name Listening to only the MC-1 EffectPCM Effects and Parameters3 PanoramaNightclub PCM Effects and Parameters Concert Hall ChurchCathedral PCM Effects and Parameters Party ChannelMusic Surround PCM Effects and Parameters Music Logic LogicPCM Effects and Parameters TV Matrix Pro LogicTHX Cinema PCM Effects and Parameters Mono Logic PCM Effect ParametersPCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters AC-3 Effects and Parameters4 AC-3 Status DisplayAC-3 Status AC-3 Effects and Parameters 2-Channel MusicAC-3 Effects and Parameters Logic Dolby DigitalAC-3 Effects and Parameters THX 5.1 Including Surround EXAC-3 Effect Parameters AC-3 Effects and Parameters AC-3 Effects and Parameters DTS Effects and Parameters5 DTS 2-ChannelDTS Music DTS Effects and Parameters DTS Logic DTS FilmDTS Effects and Parameters DTS THX Including Surround EX DTS Effect ParametersDTS Effects and Parameters Troubleshooting TroubleshootingProblem Possible Cause and Solution Troubleshooting Routine Maintenance Restoring DefaultsSpecifications SpecificationsInstallation Worksheet Inputs