Ruinet Utility User Manual
Page 11 of 46
2.3.1.Connection Overview – Settings Aspect.
Parameter | Description |
|
|
|
|
|
|
|
| |||
Connection | The current connection out of the total number of connections. |
| ||||||||||
Adapter | An adapter ID is displayed if the driver is an adapter driver. |
|
| |||||||||
Poll_Delay | The minimum amount of time that must pass between one Client Map | |||||||||||
Descriptor completing its task and the next Client Map Descriptor being | ||||||||||||
| serviced. Refer to Driver Manuals. |
|
|
|
|
| ||||||
Low_Pri_Poll_Delay | The poll delay used for lower priority Map Descriptors. |
|
|
| ||||||||
| When an upstream device polls the FieldServer, and the data is | |||||||||||
| unavailable or too old, the driver generates a poll to the downstream | |||||||||||
Server_Hold_Timeout | device for fresh data, (port expansion). The Server_Hold_Timeout | |||||||||||
| defines the time available for this transaction to complete before an error | |||||||||||
| is returned. The default is 2 seconds. |
|
|
|
|
| ||||||
Protocol | The name of the protocol used by this connection. |
|
|
| ||||||||
IP_Address | An IP address for the connection if applicable. |
|
|
|
| |||||||
Remote_IP_Address | A remote IP address for the connection if applicable. |
|
|
| ||||||||
Port | Identifies the port for a serial driver. P1... P8 or R1...R2 |
|
|
| ||||||||
Timeout* | The timeout defined for the connection. Default 2 seconds. See Error! | |||||||||||
Reference source not found. for further information. |
|
|
| |||||||||
|
|
|
| |||||||||
Recovery_Interval | The | time | after a | node | goes | tries | to poll | the | ||||
device again. Default 30 seconds. |
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||
Probation_Delay | The length of time communication needs to be | |||||||||||
an offline Client node is marked |
| |||||||||||
|
| |||||||||||
Connection_Mode | Server (passive) or client (active). |
|
|
|
|
| ||||||
Client/Server_Mode | Optional setting to force a connection mode. Possible values are Server, | |||||||||||
PLC, Hot_Standby, Hot_Standby_Data, Client_Only, Diagnostic. |
| |||||||||||
|
| |||||||||||
Multidrop_Mode | Indicates whether Multidrop mode is enabled or not. | Refer to Error! | ||||||||||
Reference source not found. for more information. |
|
|
| |||||||||
|
|
|
| |||||||||
Turnaround_Delay | The delay that the driver imposes between receiving a poll and sending a | |||||||||||
response. The default is 5ms for serial drivers. |
|
|
|
| ||||||||
|
|
|
|
| ||||||||
Baud | Connection baud rate used by serial drivers. Some drivers override this | |||||||||||
value because the communication protocol allows the baud rate to be | ||||||||||||
| changed by the master. |
|
|
|
|
|
|
| ||||
Data_bits | The | number of | data | bits used for | serial | communication by | the | |||||
connection. The values are 7 or 8. |
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||
Parity | The parity mode used by the connection to detect communication errors. | |||||||||||
Values are even, odd or none. The default is none. |
|
|
| |||||||||
|
|
|
| |||||||||
Stop_Bits | The | number of | stop | bits used for | serial | communication by | the | |||||
connection. The values are 1 or 2. |
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||
Line_drive_on | Time | a | serial | driver | using | will | wait before | driving | the | |||
communications line after receiving permission. Default is 1milisecond. | ||||||||||||
| ||||||||||||
Line_drive_off | Time that a communication line using | |||||||||||
being released, after the last bit has been sent. Default 1milisecond.. |
| |||||||||||
|
| |||||||||||
IC_timeout | Time a driver will wait between receiving the first and second bytes of a | |||||||||||
message before generating an IC Timeout. Default 0.5 seconds. | See | |||||||||||
| Error! Reference source not found. for more information. |
|
| |||||||||
IP_port | Determined by specific driver or protocol used. See Driver Manual. |
| ||||||||||
Remote_IP_Port |
|
|
|
|
|
|
|
|
|
|
| |
Max_Master |
|
|
|
|
|
|
|
|
|
|
| |
Max_Info_Frames |
|
|
|
|
|
|
|
|
|
|
| |
Connection_Type |
|
|
|
|
|
|
|
|
|
|
|
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408)