FieldServer 1.1 user manual Node Overview Error Statistics Aspect

Page 23

Ruinet Utility User Manual

Page 23 of 46

Parameter

Description

TCP Send Failed

2.4.4.Node Overview - Error Statistics Aspect

	Parameter	Description
	Node	The current node being displayed out of the total number of
	Node	nodes.
		nodes.
	PEX No slave
	Server Overruns
	Server Hold Timeouts
	Timeouts
	Checksum Errors
	Protocol Errors
	Noise
	Bad Length
	Bad Node
	Bad Function
	No Start
	PLC exception
	NAK
	Streaming
	Premature
	Preamble
	IC Timeouts	Refer to Section 2.3.3 for a description. On this screen the
	Address Errors
	Address Errors	count applies to the node only.
	Data Object offline
	Node Offline
	Msg Ignored
	Sys Cleared
	Squelch TX
	Squelch RX
	Segmentation Not Supported
	Passthru Retries
	Passthru Overruns
	Passthru Early Retries
	Passthru Normal Retries
	Passthru Early Overruns
	Passthru Normal Overruns
	Passthru Early Overrun Fails
	Passthru Normal Overrun Fails
	PWT Expired

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com

Image 23

Contents Version Rev RuinetTable of Contents Appendix C Advanced Topics Software Installation and SetupGeneral Overview PC Requirements HardwareRemote User Interface RuiNet Connecting to a FieldServer FieldServer Information FieldServer Information Settings AspectParameter Description FieldServer Information Settings AspectFieldServer Information Status Aspect Connection Overview Screen Connection OverviewConnection Overview Settings aspect Reference source not found. for further information Connection Overview Settings AspectConnection Overview Status Aspect Connection Overview Statistics Aspect Descriptor. See Error! Reference source not found Parameter Description NAK Connection Overview Error Statistics AspectConnection Overview API Aspect Parameter Description Node Overview Screen Node Overview Node Overview Settings Aspect Node Overview Operating Statistics Aspect Node Overview Status AspectParameter Description Node Overview Error Statistics Aspect Map Descriptor Overview Screen Map Descriptor OverviewMap Descriptor Overview Status Aspect Map Descriptor Overview Settings AspectMap Descriptor Overview Operating Statistics Aspect Map Descriptor Overview Error Statistics Aspect Data Array Detail Screen Data Array OverviewDriver Messages Error MessagesProcedure for Downloading a File from a PC to a FieldServer Download Configuration to FieldServerProcedure to Upload a File from a FieldServer to a PC Upload Configuration from FieldServerChange IP Address Procedure to Change a FieldServer’s IP AddressObtain the IP address using the Dhcp Client Obtain the IP address using the FieldServer’s Dhcp Server Restart FieldServer Change UI Display ModePage Appendix A.2. File Download Appendix B.4. The Most Recently Connected FieldServer -p Appendix B.2. Connecting to a FieldServer using Name -yAppendix B.3. Broadcast Mode -ib Appendix B.5. Disable Auto Connect Mode -m0Appendix B.8. Transferring files -l, -f Appendix B.6. Restart a FieldServer -bAppendix B.7. Startup Screen Appendix B.10. Uploading Files -u1 Appendix B.9. Downloading Files -u0Appendix B.14. Set Local File Name for a Transfer -l Appendix B.11. Forcing a Download -oAppendix B.12. Number of File Transfer Tries -n Appendix B.18. Skip date and time check on connect -m1 Appendix B.15. Help -hAppendix B.16. Create a Log File -a Appendix B.17. Version Information -v, -veAppendix B.19. Delete a File -z Appendix B.21. Set Timeout -kAppendix B.22. Run in Test Mode Appendix C.2. FieldServer Tiers Diagram below shows how this is typically done Appendix C.3. Connecting to a FieldServer over the InternetParameter Default Setting Appendix D. Default settings for parameters