Bosch Appliances D9412GV2 manual SDI RPS Parameters, Enable SDI RPS

Page 128

D9412GV2/D7412GV2 Program Entry Guide 6.0 GV2AUX

EN 128

6.4SDI RPS Parameters

Configure remote programming software (RPS) parameters when communicating over a private local- area network (LAN) or wide-area network (WAN). To allow RPS to communicate with a control panel over a LAN or WAN, an SDI-Ethernet two-way network interface module (NIM) and an RPS (version 3.8 or higher) are required. The computer on which RPS is installed needs a network card. See your information systems administrator for network requirements.

This section allows you to:

•Define the RPS parameters necessary to communicate by an external modem that can be connected to a D9133DC Direct Connect Programming Module.

•Provide for local programming by a DX4010i or D9133DC Serial Interface Module.

•Provide remote programming by a Conettix DX4020 or D9133TTL-E Ethernet Network Interface Module.

•Provide enhanced route paths for event reporting through a network using a DX4020 Network Interface Module.

Although not listed in this section, RPS checks for the RPS pass code (refer to Section 2.7 RPS Parameters on page 32), Datalock Code, and control panel type to determine if this RPS session should continue.

The RPS via Phone? prompt (Figure 6 on page 129), if selected, contacts RPS by the control panel phone line and not the external modem. Users cannot start an RPS session by the external modem. If you are using an external modem, RPS sessions can be started only by programming Answer Armed and Answer Disarmed (to a value greater than 0) or by setting RPS Line Monitor to Yes (refer to Section 6.4.2 Using an External Modem on page 130).

6.4.1User Interface Modifications for COMMAND 43

COMMAND 43 can communicate with RPS by a network path. Figure 6 on page 26 shows the structure of COMMAND 43.

Pressing the [ESC] key during the display of

CONTACT RPS?, ANSWER NOW?, RPS VIA PHONE?, or RPS VIA NETWORK? exits the user to Idle Text.

Enable SDI RPS

Default:

 

Yes

Selection:

 

Yes or No

Yes

 

Enable RPS sessions over the SDI

 

 

bus.

 

 

Do not enable RPS sessions over

No

 

 

 

the SDI bus.

 

 

 

Enable SDI RPS determines if the control panel allows RPS communications over the SDI bus. This item must be set to Yes if you plan to use the external modem configuration, a private LAN or WAN, or local RPS programming.

If the reset pin is in the locked position, local RPS programming is allowed even if this prompt is set to No.

When Enable SDI RPS is configured to allow for local programming, Jumper 8 in the SIM must be shorted or closed, power must be removed and reapplied after changing the address, and a standard serial null-modem cable is required.

Bosch Security Systems, Inc. 10/08 F01U003636-04

Page 127 Page 129
Image 128
Page 127 Page 129
Contents D9412GV2/D7412GV2 Type Styles Used in this Manual Prompt Sub-PromptTable of Contents Programming Prompts Directory TablesSIA CP-01 Quick Reference Using this Program Entry Guide Differences between the D9412GV2 and D7412GV2 FeaturesLiterature Referenced Document Name Part NumberProduct Handlers GV2MAINProgramming the Control Panel with the D5200 Programmer Programming Error DisplaysGuide to Programming Options Guide to UL 864 Programming Requirements Settings Permitted in UL UL 864 Programming Recommendations Prompt Possible Settings RecommendationDefault Blank Selection Up to 24 characters do not enter For SIA CP-01 Compliance Call Waiting DisablePhone PhoneDefault Yes Selection Yes or No Phone ParametersModem Format Modem IIIa2 CommunicationPoint/User Flag Conettix D6600/D6100Alarm On Fail Phone Supv TimeDtmf Dialing Fail is Yes and CC Trouble Tone is YesRouting Buzz on FailTwo Phone Lines Bfsk Duress CodeProgramming Primary and Backup Destinations Route Number Groups Which Has the Highest Priority?Enhanced Routing Programming a Duplicate ReportView Events? # Backup Device# Primary Device Fire Reports Burglar ReportsFire Reports Selection Report Description Burglar ReportsUser Reports Test ReportsUser Reports Selection Report Description Sending Test ReportsDiagnostic Reports Selection Description Test Reports Selection DescriptionRPS Reports Relay ReportsAutoFunc Reports Point Reports Selections Description Point ReportsRPS Reports Selections Report Description Access Reports Access Reports Selections Report DescriptionUser Chng Reports User Change Reports Selections DescriptionEnhanced Routing .4 Enhanced Routing on Programming a Primary and Backup DestinationEnhanced Routing RG# Backup SDI RG# Backup SDI, and EnhancedRG# Primary SDI RG# Primary PagerPager Display Fields Programming the Pager Phone NumberEvent Descriptions, Priorities, and Numbers Event Priorit Event Description NumberAC Fail Time Power SupervisionDefault Selection 1 to 90 Blank and 0 are invalid AC Fail/Res Rpt Default 60 sec Selection 10 to 300 sec in 5-sec IncrementsAC Fail Display Printer Parameters ## A1 through A8 in Scope ## Supervised## Scope RPS Parameters RPS Passcode Log % FullRPS Call Back RPS Line MonitorAnswer Armed Answer DisarmedDuress Type MiscellaneousRPS Ph Cancel Report Area ParametersArea # Area OnProgramming Account Numbers in 9000 Series Control Panels Programming Four-Digit Account NumbersProgramming Four-Digit Account Numbers D5200 Programmer Programming Ten-Digit Account Numbers# Delay Res # FA Bypass Max# Auto Watch # Exit ToneVerify Time to 60 sec # Duress Enable# Duress Enable must be set to Yes # Area Type Shared-Area Characteristics Arming a Shared Area Access Control Readers Assigned to the Shared AreaDisarming a Shared Area Shared Area Arming Sequence# Fire Time # Fire Pat# Burg Time # Burg PatRing # Single Ring# Bell Test # Acct O/C # Disable O/C in Window # Area O/C# Auto Close # Fail to OpenIf Disable O/C in Window is # Fail to Close# Restrictd O/C Exit Dly TimeDefault Selection 0000 to Arming Features# Perimeter O/C # Latest Close TimeParameter Setup Requirement To Early Ambush Timer on# Early Ambush D1255 Keypad# Exit Restart # Arm No Exit# Exit Warning # Exit Warning must be set to Yes# Entry Warning # Entry Warning must be set to YesCC# Supervised Keypad Command CenterCmd Center Default Blank Selection To 128, A, B, C, and Blank CC# Area AssignCC# Scope CC# A1through A8 in ScopeCC# Assign Door Default Blank Selection 1 to 8, BlankCC# Entr Cycl Dr CC# Trouble Tone CC# Entry ToneCC# Exit Tone CC# Arm Now WarnCC# Close Door CC# EnhancCmdCtrCC# Passcode Follows Scope ## Passcode ArmCC# Cancel Display CC# Scroll LockCC# Menu Key Lock CC# Abort DisplayArea# Is On Area# Not ReadyArea# Is Off Area# Acct Is OnCustom Function CF### TextCF### Key Strokes See .10.2 Area Text onExample Programming Custom Function KeystrokesCF### Custom Function Keystrokes Commands User InterfaceKeypad Selections Keypad Programming ChoicesMaster Arm Delay Perim DelayWatch Mode Mstr Arm InstPerim Partial View Area StatView Memory View Pt StatusAccess Ctl Level Door ControlChg Time/Date Chg PasscodeDel User Extend ClosePrint Log User CmdBypass a Pt Unbypass a PtChange Relay Remote ProgramService Walk Display RevChange Skeds Invisible Walk TestFunction 128 through Authority Level## Disarm Custom Functions## Master Arm Delay ## Perim Delay## Watch Mode ## Mstr Arm Inst## View Memory ## View Pt Status## Walk Test ## Fire Test## Send Report ## Door Control## Cycle Door ## Unlock Door## Access Ctl Lvl ## Chg Display## Chg Time/Date ## Chg Passcode## Del User ## Extend Close## User Cmd ## View Log## Reset Sensors ## Change Relay## Remote Program ## Display Rev## Service Walk ## Default Text## Change Skeds ## Invisible Walk Test## Perimeter O/C ## C Function 128 through## Force Arm ## Area O/C## Security Level ## Disarm Level## Function Level Level or L## Disarm Level authority to#6 Watch Mode Default Refer to the program record sheet SelectionFunction List Menu ItemRelay Parameters ## CC Address 1 throughArea Relays # Alarm Bell# Reset Sensors # Watch Mode # Area Fault# Force Armed # Area Armed# Perim Fault # Silent AlarmGround Fault Detect # Duress RelaySummary Alarm Phone FailComm Fail Summary Fire TblSummary Trouble Summary SupBurgPass Code or Token Worksheet User ### Reporting and LoggingUser pass code User token or card Bsfk User Code Report### Area 1 through Area 8 Auth ### Passcode### User Group ### Name ### Mstr Site### Mstr Crd Data ### SU1 through SU3 SitePoint Index Point Index## Type Description Selection ## Type Description Normal OpenShort Disarmed is Yes## Response of 8-9-A-B-C Point ResponsesApplications for Point Responses 9, D, and E ## Pt Response Hour PointsExample of Controlled point Example of 24-hour point## Entry Delay ## Silent Bell## Invisible Pt ## Ring Til Rst## Audible After 2 Failures ## Buzz On Fault Keypad for any fault condition while the point## Watch Point Point Response## RlyResp Type ## Disp as Dvc## Local While Disarmed Relay Follows Point The relay## FA Retrnable ## Disable Rst## Local While Armed ## BP Retrnable ## BypassableA# Auto Close prompt 5 Open/Close Options## Report Bypass at Occurrence ## Cross Point## Resettable ## Fire Point## Alarm Abort Point Number### Point Index Parameter Abort Window### Area Assign ### Debounce### BFSK/Relay ### BFSK/Relay Codes/Relays### Point Text CMD7 Point IndexCMD7 BFSK/Relay CMD7 Point TextCMD9 Point Text CMD9 Point IndexCMD9 BFSK/Relay # Sunday WindowsWindow # Monday # Tuesday# Wednesday # ThursdayDefault Selection Hhmm hours and minutes Disable O/C in Window is programmed Yes# Open Window Start # Open Window Stop# Close Early Begin Programming to Link Two Days over Midnight# Close Window Start # Close Window Stop# Xept Holiday # Holiday# Area 1 through Holiday Indexes for O/C WindowsOpening and Closing Windows Worksheet Normal Store HoursUser Windows # UW# User GroupUW# Group Enable UW# Group DisableUW# Sunday UW# MondaySkeds UW# Xept HolidayUW# Holiday 1 through Sked Number## Point Number ## Function Code## Area 1through ## Relay Number Selections BlankTo 128 for D9412GV2 To 64 for D7412GV2 To 128 for D9412GV2## Defer Test ## Hourly ReportIf Expand Test Rpt in Phone ## Defer Status## Custom Func ## Cmd CenterCmd Center and Custom Func ## Access Ctl Level # ## Access Ctl Level### Cmd Center 1through ## Door 1 throughAccess Authority Events No Entry Events Off ## Time ## Date## Sunday ## MondayHoliday Indexes ## Xept Holiday## Holiday DateIndex 1 Days Index 2 DaysIndex 3 Days Index 4 DaysEnable SDI Auto IntroductionRPS and D5200 Handler Requirements SDI AutomationParity/Stop DTR ControlSupervision RTS ControlSDI RPS Parameters Enable SDI RPSUser Interface Modifications for Command Call Back Enabled Set RPS IP Address to 0 if Enable Ext RPS IP AddressRPS Port Number Refer to RPS IP AddressFor US Robotics Programs→Accessories→CommunicationsFor Best Data Smart One External Modem Connection PC running Remote Programming Software RPS Modem PstnD9412GV2/D7412GV2 Program Entry Guide 6.0 GV2AUX Enable Ext Modem Default Atdt Selection Not availableSeize Relay Modem Init StringEnhanced Comm Path # IP Add1Path # IP Add2 Path # IP Add3Path # PortNum Path # Poll RatePath # Poll Rate is set to 120 sec Path # Retry Count is set toExample of Retry Count Default Selection Sec to 65535 secPath # Ack Wait SDI RPS/Enhanced Communications Configuration Default Selection 300, 1200, 2400, 4800, 9600, 14.4 KPath # Retry Count Path # Anti-ReplayFire Summary Sustain Route Group AttemptsRG# 1 Attempt Enable Protocol Type Fire Supv Res TypeFire Trouble Resound Secondary Ambush CodeDefault Selection 0, 3, 4, 5, or Default Selection 3, orPasscode Length Swinger CountCross Point Parameters CrystalTime AdjPerimeter Relay Early Armed RelayCross Point Ranges Within Groups Default 20 sec Selection Sec to 255 secCross Point Time Door Profile Door ## Entry Area # #CC#ScopeDefault Blank Selection Blank, 1 to 127, 129 to # Door Point# Interlock Point Effects of Programming on Custom Function Activation# Auto Door? # Fire Unlock?# Disarm on Open? # Card TypeStrike Profile # Strike Time# Shunt Time # Buzz TimeEvent Profile # Deact On Open?# RTE Shunt Only? # REXShunt Only?# Access Granted? # No Entry?# Enter Request? # Exit Request?SIA CP-01 Quick Reference Programming the Control Panels for SIA CP--01 CompliancePower Supervision PhonePrinter Parameters Phone ParametersArming Features Keypad Command Center Assignment51Access Control Functions Bell ParametersCustom Functions Area RelaysCommand 7 and Command 104 Point Assignments 102Pass Code or Token Worksheet Point IndexHoliday Indexes 124 115144 Bosch Security Systems, Inc /08 F01U003636-04 Bosch Security Systems, Inc. F01U003636-04
Related manuals
Manual 74 pages 9.34 Kb

D9412GV2 specifications

The Bosch D9412GV2 is an exceptional dishwasher that stands out in the competitive world of home appliances. Known for its reliability and advanced features, this model offers a blend of cutting-edge technology and user-friendly design that appeals to modern households.

One of the most noteworthy features of the D9412GV2 is its impressive cleaning performance. Boasting a unique combination of powerful jets and specialized wash cycles, it ensures that even the toughest stains are removed effectively. The dishwasher features Bosch’s patented PrecisionWash system, which utilizes intelligent sensors to monitor the wash cycle’s progress and adjust the water spray for optimal cleaning results. This not only guarantees sparkling dishes but also conserves water and energy.

In terms of capacity, the D9412GV2 does not disappoint. It has a spacious interior that is designed to accommodate up to 16 place settings, making it an ideal choice for families or those who frequently entertain guests. The adjustable racks and flexible loading options allow users to maximize space and customize the dishwasher to suit their unique needs. The third rack is particularly useful for utensils and smaller items, providing additional space that enhances efficiency.

The dishwasher is also engineered with noise reduction features for a quieter operation. With a sound rating of 44 decibels, it operates silently in the background, allowing for uninterrupted conversations and a peaceful home environment. This is especially beneficial for open-concept living spaces.

Energy efficiency is another hallmark of the Bosch D9412GV2. It is Energy Star certified, reflecting its commitment to sustainable practices. It uses less water and electricity without compromising performance, making it a responsible choice for eco-conscious consumers.

Moreover, the presence of the Home Connect feature allows users to control and monitor their dishwasher remotely via a smartphone app. This innovative technology enables users to start or stop cycles, receive notifications, and even download new wash programs, adding convenience and flexibility to busy lifestyles.

In conclusion, the Bosch D9412GV2 is a state-of-the-art dishwasher that excels in cleaning performance, capacity, and energy efficiency. With its innovative technologies and thoughtful design, it represents Bosch's commitment to quality and customer satisfaction, making it a valuable addition to any kitchen.
Top Page Image Contents