OPERATION
Panic
Pressing the panic button on the control panel will cause the siren to sound and outgoing calls will be made to the
To stop the siren and disarm the system, user can enter a valid password. This will terminate the siren and the control panel from calling the rest of the emergency phone numbers.
System Failure
Control Panel constantly monitors itself and its sensors. If there are any trouble conditions, the control panel will advise the user. These trouble conditions include:
-Phone Line Failure
-Sensor Failure (loss of supervisory signal)
-Low Battery – Control Panel
-Low Battery – Sensors
Phone Line Failure
When the phone line is disconnected or malfunctions, the control panel will instantly notify the user by:
1.Both Power [PWR] and Program [PROG] LEDs will flash together;
2.Voice announcement “Phone Line Failure” will be played.
When phone line failure occurs, please check the phone line connection, ensure the phone line is plugged into both the control panel and the wall socket securely. You should also check the phone line with a normal telephone to determine if it can dial out to a phone number. If it cannot dial out, that indicates the phone line is not in service, you should contact your local phone company.
ADVANCED PROGRAMMING
Remote [6] is represented by zone LED 1
®
ZONE LED | REMOTE LOCATION |
|
|
1 | 6 |
|
|
2 | 7 |
|
|
3 | 8 |
4 | 9 |
5 | 0 |
Erase Keychain / Keypad Remotes
Follow the instructions below to erase keychain or keypad remotes / receivers.
Step |
| Keys |
| Function | Description | Note | |
|
|
|
|
|
|
| |
1 |
| [PROG] | Enter | Enter master | 3 beeps for valid | ||
|
| [MPIN] |
| Programming | password to pro- | password. 1 long beep | |
|
|
|
|
| mode | gramming mode | for invalid password. |
2 |
| [0] |
|
| Select erase |
| After [0] is entered, some |
|
|
|
|
| remote |
| zone LEDs will flash or stay |
|
|
|
|
| programming |
| off. The zone LEDs |
|
|
|
|
|
|
| represent whether that zone |
|
|
|
|
|
|
| is occupied by any remote. |
|
|
|
|
|
|
| ** See Table B below. |
3 |
| To erase | Select remote | Select a remote | After you have selected the | ||
| an occupied | location you | location [6], [7], | remote location, you will hear 3 | |||
|
| remote, press | would like to | [8], [9] or [0]. | beeps and verbal confirmation | ||
|
| [6] to [0]. | erase |
| [Device X Empty Memory], | ||
|
|
|
|
|
|
| where X is the remote location |
|
|
|
|
|
|
| you have selected. |
|
|
|
|
|
| ||
ZONE LED |
|
| DESCRIPTION |
|
| ||
|
|
|
|
| |||
Off |
|
| Zone is not occupied by any remote |
| |||
|
|
| |||||
Flashes twice |
| This zone is occupied by a remote. You may select this zone to | |||||
|
|
|
| erase this remote. |
|
| |
|
|
| |||||
Flashes once |
| This zone is occupied by a control module (Optional). | |||||
|
|
|
| THIS IS NOT A REMOTE CONTROL, THEREFORE, SHOULD NOT BE | |||
|
|
|
| ERASED. (Refer to page 40 Erase Control Module for more | |||
|
|
|
| information) |
|
| |
|
|
| |||||
Flashes once, |
| This zone is occupied by a remote AND a control module. | |||||
then twice |
|
| You may select this zone to erase the remote. | ||||
|
|
|
|
|
|
|
|
**Table B: Zone LED status for erasing keychain/keypad remote(s).
*Please refer to erase control module on page 40.