ADVANCED PROGRAMMING
Follow the procedures below to program the beep / alarm setting.
Step | Keys | Function | Description | Note |
|
|
|
|
|
1 | [PROG] | Enter Programming | Enter master | 3 beeps for valid password. |
| [MPIN] | mode | password to | 1 long beep for invalid |
|
|
| programming mode | password. |
|
|
|
|
|
2 | [5] | Select Beep / |
| After [5] is entered, some zone |
Alarm Setting |
| LEDs will flash or stay on. | ||
|
|
| ||
|
|
|
| This indicates whether that |
|
|
|
| zone is set to beep or alarm. |
|
|
|
|
|
3 | Set to Beep: | Select which | Refer to the | If Alarm is set for that zone, |
| [1] to [5] | zone you would | diagram below to | that zone LED will be on. If |
|
| like to Beep or | select the appro- | Beep is set, the LED will |
| Set to Alarm: | Alarm. | priate setting. | flash. You are allowed to |
|
|
| make multiple changes before | |
| [6] to [0]. |
|
| |
|
|
| terminating programming | |
|
|
|
| |
|
|
|
| mode. |
|
|
|
|
|
4 | [PROG] when | Terminate pro- |
| PROG LED will be off, and |
| finished. | gramming mode. |
| you will hear 3 beeps. |
|
|
|
|
|
COMMUNICATION
Table 1: Remote Phone Operations
SYSTEM OPERATION | PHONE COMMAND | DESCRIPTION |
|
|
|
Turn on device x | x+[*] | Turn devices on will hear [Device X On]. When the |
[x] = 1 to 5 |
| control module receives the on signal, it will turn on the |
|
| plugged in device, and send a confirmation back to the |
|
| control panel. You will then hear [Device On Accepted]. |
|
|
|
Turn off device x | x+[#] | Turn devices off will hear [Device X Off]. When the |
x = [1 to 5] |
| control module receives the off signal, it will turn off the |
|
| plugged in device, and send a confirmation back to the |
|
| control panel. You will then hear [Device Off Accepted]. |
|
|
|
Check system status | [8]+[#] | You will hear system status announcement |
|
|
|
Arm | [7]+[#] | You will hear [System Armed] |
|
|
|
Disarm | [9]+[#] | You will hear [System Disarmed] |
|
|
|
Disconnect | [0]+[#] | Phone line disconnect |
|
|
|
|
|
|
|
| ® |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| BEEP | ALARM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 1 | Button [1] | Button [6] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 2 | Button [2] | Button [7] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 3 | Button [3] | Button [8] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Zone 4 | Button [4] | Button [9] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 5 | Button [5] | Button [0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This row : Buttons for Beep
Zone LED : Flash
This row : Buttons for Alarm
Zone LED : ON
Example:
If you would like to change the setting for zone 5 from “Beep” to “Alarm”, simply press [0] at step 3.
This will change the zone 5 setting to “Alarm”.