Learn Keychain / Keypad Remotes

ADVANCED PROGRAMMING

Additional keychain or keypad remotes can be programmed to the control panel. Maximum of 5 keychain/keypad remotes can be programmed to the control panel.

-Keychain or keypad remotes should be programmed to Device 6 to Device 0.

Follow the instructions below to program remote(s) to remote location(s) 6, 7, 8, 9, or 0, which is the bottom row of the numeric keypad of the control panel.

Step	Keys		Function	Description	Note

1	[PROG]		Enter Program-	Enter master	3 beeps for valid
	[MPIN]		ming mode	password to	password. 1 long beep
				programming mode	for invalid password.
2	[4]		Select learn		After [4] is entered, some
			remote		zone LEDs will flash or
			programming		stay off. The zone LEDs
					represent whether that
					zone is already occupied
					by another remote.
					** See Table A below.

3	[6] to [0]		Select remote	Select a remote	After you have selected
			location	location [6], [7],	the remote location, that
			(Max. 5 remotes)	[8], [9] or [0].	zone LED will be on.

4	Activate the		Trigger remote	Once the signal is	You will hear
	remote by			transmitted to the	[Device X Accepted],
	pressing any			Control Panel, that	where “X” is the remote
	one of the			signal which will	location.
	buttons.			be stored.

ZONE LED		DESCRIPTION

Off		Zone is not occupied by any remote

Flashes twice		This zone is occupied by another remote. Programming another
		remote to this zone will overwrite the previous remote.

Flashes once		This zone is occupied by a control module* (Optional).
		You can still program a remote to this zone, and it will not overwrite
		the control module* you have in this zone. (Refer to page 37 Home
		Automation for more information)

Flashes once,		This zone is occupied by a remote AND a control module*.
then twice		If you program another remote to this zone, it will overwrite the
		previous remote, but not the control module*.

**Table A: Zone LED status for learning keychain/keypad remote(s).

*Please refer to learn control module on page 37.

–32–

OPERATION

Sensor Failure

The control panel constantly monitors its sensors, if the control panel fails to communicate with any sensors, it will notify the user by:

1.The zone LED of the failed sensor will be on steadily;

2.Voice announcement “zone X sensor Y failure” will be played.

When sensor failure occurs, try the following:

1.Check if the sensor is located at where it should be, and whether there is any physical damage to the sensor.

2.If the failed sensor is not physically damaged, try to activate the sensor and

see

if the control panel reacts to such activation.

3.If not, try to remove the sensor from its location, and bring it closer to control panel and activate the sensor. It is possible that the sensor is installed too far from the control panel and it cannot establish a steady communication with the control panel. If this is the case, please install the sensor closer to the control panel.

Low Battery

Control Panel

The control panel is powered mainly by the adapter. However, during power outage, it will be powered by the rechargeable backup battery. Under standby conditions, these batteries can last for 48 hours.

When the backup battery is running low, the “LO BATT” LED on the control panel will be on, indicating the backup battery should be recharged. To recharge the backup battery, plug in the power adapter. It takes approx. 20 hours to fully charge the backup battery.

Sensors (Sold seperately)

All of the sensors are battery powered. Depending on the operating condition and environment, the battery life varies from 9 months to 2 years. 9V alkaline battery is used for the motion sensor, the battery life is approximately 9 months. Door / Window Sensor operates on a Lithium CR-2032 battery, with battery life of approximately 2 years. For other sensors, please refer to the user’s instructions regarding the battery life.

–21–

ADVANCED PROGRAMMING