Sharp EC-T5180 How To Clean The Net Filter Assembly, How To Clean The Main Filter, Filter Cover

Page 12

HOW TO CLEAN THE NET FILTER ASSEMBLY

MAINTENANCE INSTRUCTIONS

HOW TO CLEAN THE NET FILTER ASSEMBLY

1	Slide net filter assembly out of dirt compartment.
2
	(Fig.25)Unscrew the filter element from the assembly.
3
	Wipe excess dust from the net filter.
4		Unscrew

	Wash net filter with water, using a soft sponge.
5
	Allow net filter assembly to completely dry before
	replacing it, then insert it into the dirt

compartment.

CAUTION: Do not use chemicals, bleach or hot water to clean the dirt compartment. Wash with water using a soft sponge. Do not dry with hair dryer or heater.

Net Filter

Filter Assembly

Fig.25

HOW TO CLEAN THE MAIN FILTER

	1	Hold the top handle glip, and release the filter	Filter Clamp
		clamp then remove the filter cover to open.

Filter Cover

2	filter.Remove main filter from the filter box and scrub the
3
	Wash the filter with soap and water.
4
	Allow the filter to completely dry before putting
	back in the filter compartment.
5
	Replace the filter cover onto the filter compartment,
	interlocking the latch portions.

Top Handle Grip

Latch Portion

Filter Compartment

Main Filter

Fig.26

CAUTION: Do not use a washing machine for cleaning. Do not dry with hair dryer or heater. Be sure the filter is set in the right position.

NOTE: For maximum performance we recommend to clean this filter every time you empty the dirt compartment.

12

Image 12

Contents CONTENTS VACUUM CLEANEREC-S5170 EC-T5180 EC-T5180A EC-T5180B MODELSIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSSPECIFICATIONS PARTS IDENTIFICATIONFRONT REAR Cord Storage Hook Carrying Handle Power CordON/OFF Switch Dirt Compartment Handle UpperHOW TO ATTACH THE HANDLE TO VACUUM CLEANER HOW TO WIND POWER CORDHOW TO RELEASE POWER CORD OPERATING INSTRUCTIONSHOW TO RELEASE THE HANDLE HOW TO OPERATE RUG /FLOORSELECTOR PEDALNOTE Agitator Safety Mechanism Upright PositionON/OFF SWITCH POWER CONTROL SWITCH EC-T5180series onlyPOWER HIGH OPERATING INSTRUCTIONSHOW TO USE THE ON BOARD TOOLS HEAT PROTECTION SYSTEMMAINTENANCE INSTRUCTIONS HOW TO REMOVE AND REPLACE DIRT COMPARTMENTFig.21 Air Duct Fig.22 Net Filter assembly STEPSTEP Dirt CompartmentHOW TO CLEAN THE NET FILTER ASSEMBLY HOW TO CLEAN THE MAIN FILTERNet Filter Filter CoverHOW TO REMOVE / AND RESET THE BOTTOM PLATE Fig.28 RESETSuction Hose Front channel REMOVEHOW TO REMOVE THE HEAD COVER MAINTENANCE INSTRUCTIONSREPLACEMENT INSTRUCTIONS HOW TO REPLACE THE HEADLIGHT LAMPHOW TO REPLACE THE MAIN FILTER HOW TO MAINTAIN OR REPLACE THE EXHAUST FILTERS How to remove/set the filterREPLACEMENT INSTRUCTIONS HOW TO REPLACE THE BELT AND OR AGITATOR ASSEMBLY Agitator Assembly Main Pulley Fig.41 Idler PulleyFlat Belt Motor ShaftBEFORE REQUESTING SERVICE TROUBLESHOOTING CHARTProblem FOR CUSTOMER ASSISTANCEDESCRIPTION OF ACCESSORIES PARTS DESCRIPTIONPART NUMBER PARTS DESCRIPTIONCONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey SHARP CORPORATION Osaka, JapanASPIRADORA INSTRUCCIONES DE OPERACION ADVERTENCIA / dañosINSTRUCCIONES DE SEGURIDAD IMPORTANTES Problema SERVICIO AL CONSUMIDORNOTA GUARDE ESTAS INSTRUCCIONESDESCRIPCION DE LOS ACCESORIOS ARTICULODESCRIPCION ARTICULO NUMERO DE PARTEGARANTIA LIMITADA SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey SHARP CORPORATION Osaka, Japan