Sharp EC-T5180A How To Replace The Belt And Or Agitator Assembly, Flat Belt, Motor Shaft

Page 17

HOW TO REPLACE THE BELT AND OR AGITATOR ASSEMBLY

HOW TO REPLACE THE BELT AND OR AGITATOR ASSEMBLY

When replacing the belt, always set the RUG/FLOOR Selector pedal in the "FLOOR" position.

1	After removing the bottom plate (see page 13)	Motor Shaft
1	to determine if the belt or the agitator is worn or
	broken.
2	Pull out the agitator and then remove the flat
2	belt from the motor shaft. (Fig. 42)
	Flat Belt

3	Loop the (new) belt around the motor shaft and
	(new) agitator as shown. (Fig. 42)

Agitator Assembly

Main Pulley Fig.41 Idler Pulley

4 Then re-insert the (new) agitator assembly, making sure that both ends of the agitator assembly fit in the groove of the nozzle head. (Fig. 43) Be sure to install the new flat belt into the belt guide properly. (Fig. 43)

Motor Shaft

Idler Pulley Flat Belt

Arrow

Main Pulley

5	Be sure that the flat belt is not twisted and all
	rotating parts move smoothly. (Fig.43)

And secure the bottom plate with four screws. (see page 13)

(To insert the agitator assembly into the nozzle head, follow the Arrow

direction as indicated.)

Fig.42

Belt Guide

Agitator Groove

Fig.43

17

Image 17

Contents VACUUM CLEANER CONTENTSEC-S5170 EC-T5180 EC-T5180A EC-T5180B MODELSIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONSFRONT SPECIFICATIONSPARTS IDENTIFICATION Cord Storage Hook Carrying Handle Power Cord REARON/OFF Switch Dirt Compartment Handle UpperHOW TO WIND POWER CORD HOW TO ATTACH THE HANDLE TO VACUUM CLEANERHOW TO RELEASE POWER CORD OPERATING INSTRUCTIONSHOW TO OPERATE RUG /FLOORSELECTOR PEDAL HOW TO RELEASE THE HANDLENOTE Agitator Safety Mechanism Upright PositionPOWER CONTROL SWITCH EC-T5180series only ON/OFF SWITCHPOWER HIGH OPERATING INSTRUCTIONSHEAT PROTECTION SYSTEM HOW TO USE THE ON BOARD TOOLSHOW TO REMOVE AND REPLACE DIRT COMPARTMENT MAINTENANCE INSTRUCTIONSSTEP Fig.21 Air Duct Fig.22 Net Filter assemblySTEP Dirt CompartmentHOW TO CLEAN THE MAIN FILTER HOW TO CLEAN THE NET FILTER ASSEMBLYNet Filter Filter CoverFig.28 RESET HOW TO REMOVE / AND RESET THE BOTTOM PLATESuction Hose Front channel REMOVEMAINTENANCE INSTRUCTIONS HOW TO REMOVE THE HEAD COVERHOW TO REPLACE THE MAIN FILTER REPLACEMENT INSTRUCTIONSHOW TO REPLACE THE HEADLIGHT LAMP REPLACEMENT INSTRUCTIONS HOW TO MAINTAIN OR REPLACE THE EXHAUST FILTERSHow to remove/set the filter Agitator Assembly Main Pulley Fig.41 Idler Pulley HOW TO REPLACE THE BELT AND OR AGITATOR ASSEMBLYFlat Belt Motor ShaftTROUBLESHOOTING CHART BEFORE REQUESTING SERVICEProblem FOR CUSTOMER ASSISTANCEPARTS DESCRIPTION DESCRIPTION OF ACCESSORIESPART NUMBER PARTS DESCRIPTIONSHARP ELECTRONICS CORPORATION CONSUMER LIMITED WARRANTYSharp Plaza, Mahwah, New Jersey SHARP CORPORATION Osaka, JapanINSTRUCCIONES DE SEGURIDAD IMPORTANTES ASPIRADORA INSTRUCCIONES DE OPERACIONADVERTENCIA / daños SERVICIO AL CONSUMIDOR ProblemaNOTA GUARDE ESTAS INSTRUCCIONESARTICULO DESCRIPCION DE LOS ACCESORIOSDESCRIPCION ARTICULO NUMERO DE PARTESHARP ELECTRONICS CORPORATION GARANTIA LIMITADASharp Plaza, Mahwah, New Jersey SHARP CORPORATION Osaka, Japan